ReviewsMicrocontroller Servo Board

15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

  • You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
  • Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
  • Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
  • Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
  • Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.
Check Stock

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

  • Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
  • Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
  • 2.You should connect higher power supply for higher-power servo.
  • 3.Make sure servo are connected properly, otherwise they will not move..
  • Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
  • Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
  • Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..
Check Stock

Ingcool Raspberry Pi Pico Microcontroller Board with Pre-soldered Header Low-Cost, High-Performance,Based on RP2040 Chip, Dual-core Arm Cortex M0+ Processor,Flexible Clock Running up to 133 MHz

  • Raspberry Pi Pico is a low-cost, high-performance microcontroller board with flexible digital interfaces..
  • Raspberry Pi Pico Board incorporates Raspberry Pi's own RP2040 microcontroller chip, with dual-core Arm Cortex M0+ processor running up to 133 MHz, embedded 264KB of SRAM and 2MB of on-board Flash memory, as well as 26x multi-function GPIO pins..
  • For software development, either Raspberry Pi's C/C++ SDK, or the MicroPython is available..
  • There're also complete development resources and tutorials to help you get started easily, and integrate it into end products quickly..
  • This is a Raspberry Pi Pico with Pre-soldered Header,it is easier to connect with another items..
Check Stock

Prg-108 GQ-4X V4 (GQ-4X4) Programmer + ADP-019 PSOP44 Adapter V2

  • The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families.
  • The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
  • STM8 applications use the USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software..
  • STM32 applications use the USB full-speed interface to communicate with Atollic, IAR, Keilor TASKING integrated development environments..
Check Stock

Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino

  • ... the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”)..
Check Stock

1pcs 1-Bit AC 220V Optocoupler Isolation Module

  • Output TTL level can be detected with the microcontroller. The power supply can be 3-5V.
  • the PLC input terminal of the PLC COM power supply 24V input termination of the board signal output OUT, optocoupler board GND power negative.
  • When the power module in the power of the board after the white wire frame can not touch any device .. because it is high voltage. Note the safety of electricity.
Check Stock

STLINK-V3SET Microcontrollers ST STM8 and STM32 MCU USB Swim JTAG SWD Modular Stand-Alone in-Circuit Debugger Programmer SPI I2C CAN GPIOs @XYG

  • The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and....
  • The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board..
  • The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and....
  • The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board..
Check Stock

waveshare for Raspberry Pi Pico Evaluation Kit B Include Pi Pico Board with Pre-Soldered Header,1.14inch RGB Color LCD, 10DOF IMU Sensor Module,Dual GPIO Expander,Breadboard

  • Raspberry Pi Pico Evaluation Kit inlclude Raspberry Pi Pico with pre-soldered header ,1.14inch LCD Display Module,10-DOF IMU Sensor Module,Dual GPIO Expander ,830 Quality Breadboard etc.
  • Raspberry Pi Pico Board,a tiny, fast, and versatile microcontroller board,Built Using RP2040 Microcontroller Chip Designed By Raspberry Pi.
  • 1.14" LCD Display Module for Pico ,Embedded ST7789 Driver, Using SPI Bus.
  • 10-DOF IMU Sensor Module,an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I2C bus for communication..
  • Dual GPIO Expander for Pico,Two Sets Of Standard Raspberry Pi Pico GPIO Male Headers.
Check Stock

Arduino MKR Zero with Headers [ABX00012]

  • The Central Board for your Electronic Project.
  • Powerful 32-bit Microcontroller and Micro SD Memory Card Connector.
  • Ideal for: Music, Audio processing, robotics, art installations.
  • Part of the Arduino Maker Board Family for IoT Devices, easy to configure with Arduino Software..
Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

  • 10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
  • Great for jumping from board to board or just about anything else..
  • There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
  • Length:100mm Type:JR Plug Servo Extension wire (Male to Male).
Check Stock