ReviewsModule Power Connector

5 Pack Black Light Micro Effects Light 405nm Violet LED Mini Blacklight with 9V Battery Clip for Props Scenery Fluorescent Paints Theatrical Costumes UV Glow Inks

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Use: Can be conveniently connected to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect or solder to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector Clip Lead Wire (NO battery included).

Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
NOTE: the item not include Arduino Uno module..

Harness includes VSS and SWC pins. This is an upgraded version of the Metra 70-7552. You must purchase an AXXESS ASWC-1 or similar steering wheel interface module to connect to this module. This harness only includes the wires that go to the steering wheel switches..
This adapter is used to install an aftermarket Headunit/Stereo Receiver in a 2007-up Nissan..
Dedicated ground and +12 Volt Accessory wires soldered in to power a steering wheel control interface module..
High Quality ABS Plastic Molded Connector For The Perfect Fit..
Pre-Stripped To Make Installation Quick And Easy..

8 port(2x4) RJ45 8P8C sockets, with the module you can easily connect Raspberry Pi GPIOs and Power supply to peripheral devices through the RJ45 connector. The module support all 40pin Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B Zero, Zero-W..
Each RJ45 port is connected Power Supply and GND. Each RJ45 can independently choose from the Raspberry Pi 5V / 3.3V, or from blue terminal block, to supply power to external devices. The 4 5 pin of all RJ45 ports are connected to the power supply(VCC, V+), and 7 8 pin connected to GND(0V)..
RJ45 GPIO connects: Port 1: UART(RXD TXD) GPIO17 GPIO4. Port 2: SPI(SCLK CE0 MISO MOSI). Port 3: GPIO6 GPIO12 GPIO5 CE1. Port 4: GPIO21 GPIO26 GPIO20 GPIO19. Port 5: I2C(SDA, SCL) GPIO18 GPIO27. Port 6: I2C(SDA, SCL) GPIO23 GPIO22. Port 7: I2C(SDA, SCL) GPIO24 GPIO25. Port 8: I2C(SDA, SCL) GPIO13 GPIO16..
2x20pin expansion pin header, pin height 10mm/0.39".
Packing list: 1x RJ45 breakout board, 4x brass standoffs, 8x M2.5x6 screws, 8x pin jumpers. (the item not include Raspberry Pi, RJ45 cable and plug).

SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module.
[Feature 2] SHARI PiHat uses a single circuit board which contains installed surface mount (SMD) parts as well as 2 through-hole parts, a surface mount SMA connector and the SA818 (UHF) radio module.
PiHatU also uses the Cmedia CM119B USB audio IC.

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Standard 5.5x2.1mm DC Male Plug, conveniently connect to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector with DC 5.5x2.1mm Male Plug (NO battery included).

Fit for Manual or Automatic Transmissions.
Which can be plugged into OBD2 connector of your car to increase the performance of your car..

Power module for AT892 microset. Also suitable for use with any Audio-Technica wireless essentials microphone terminated with 4-pin locking connector. The AT8539 allows you to convert your wireless microphone into a wired model. Comes equipped with a Snap-On belt clip.

Rotationally symmetric cardioid polar pattern.
Electret condenser microphone with self contained electronics eliminating the need for an external power module.
JTS rubberized isolation componentry assure super low handling noise and mechanical isolation.

Original Wireless RF Module PCB Board Power On / Off Circuit Board.
Compatible with XBOX One console ONLY, NOT FIT for Xbox One Slim or Xbox One X consoles..
Please Double Check the Model Number of Your Device in Case of Wrong Part Ordered.
Perfect replacement part for faulty/broken/damage or worn out RF Module Board.No need for or Soldering connection cables. Just plug the proprietary connector into the motherboard, and screw into place..
Please Replace This Part Under Professional Guide(You can watch some tutorial video on YouTube)Please Make Sure No Man-Made Damage or Scratch when Returning.

12V to 5V USB converter: input voltage: DC8-20V, 12V changes to 5V.
Micro USB connector and high conversion: our DC to DC converters have Micro USB charging ports.
DC to DC buck converter has an integrated switch thin regulator module, and the conversion rate is as high as 96 percent.
Intelligent protection: 12V to 5V DC converter adopts intelligent micro-processing chip, which can automatically protect against overvoltage, overcurrent, overtemperature and short circuit.
All epoxy sealed containers have waterproof housings.
Wide application: DC converter module 12V to 5V will be suitable for GPS navigation, driving recorder, electronic dog, car radio, car audio, MP3, MP4, walkie talkie, surveillance system, bus display, taxi advertising screen, driving recorder, LCD TV, LED, etc..
Warm prompt: those devices' power must be lower than 15W when use this DC/DC converter 12V to 5V, and will not be compatible with partial Samsung phones.