ReviewsOem Pilot Bearing Puller

Orion Motor Tech 3\ 4\ 6\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels (GD)

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes three puller sizes to cover most applications: a 3 inch gear puller with a 2.3" reach and 3" max. spread.
  • a 4 inch gear puller with a 3" reach and 4" max. spread.
  • and a 6 inch gear puller with a 4.7" reach and 6" max. spread..
  • Versatile Reversible Design: Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside as needed..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that these gear pullers are backed by Orion Motor Tech's warranty and friendly customer service..
Check Stock

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

Inner Camshaft Needle Bearing Installer Tool & Remover Removal Puller Fit For 2017-2022 Harley Davidson Milwaukee Eight Engine (M8)

  • ...Ultra Limited Low, 2017+ Harley Ultra Limited, 2017+ Harley Tri Glide, 2017+ Harley Street Glide, 2017+ Harley Softail, 2017+ Harley Road King, 2017+ Harley Road Glide, 2017+ Harley Freewheeler, 2018+ Harley Fat Boy, 2018+ Harley Fat Bob, 2017+ Harley Electra Glide, 2017+ Harley Breakout..
  • APPLICATION: This camshaft bearing installer tool & remove puller fit for Harley Milwaukee Eight Engines (M8) models. Compatible with all Harley Davidson twin cam..
  • FUNCTION: The bearing puller is designed to grip the needle bearings and prevent them from falling into the crankcase. The installation tools are designed to press on the outermost diameter of the bearing, eliminating damage to the bearing, cam, or housing. The pressure adapter also sets the bearing to the proper depth..
  • FEATURES: The inner camshaft needle bearing installer tool & remover puller with special style collet and fine thread. Easy to install, the design holes can be suitable for the engine, and the installation progress can be checked..
  • MATERIAL: Made of heavy-duty steel with black powder-coated finished, prevent corrosion and rust, solid and durable. The kit includes 12 pieces, including a cam bearing plate, installer tools, puller tools, and thumb screws, as the picture shows..
Check Stock

DURATECH 4-Piece 3-Jaw Gear Puller, 3', 4', 6', 8', Removal Tool for Gears, Pulleys, Bearings and Flywheels, Fully Assembled, CRV

  • Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
  • Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
  • Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 4 or 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
  • Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas. Achieve more with its adjustable and reversible jaws..
  • Use the DURATECH 3, 4, 6, and 8-Inch Gear Puller 3 Jaw Flywheel Puller Set to remove most shift-fitted parts with ease. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaf....
Check Stock

DURATECH 8-Inch 3-Jaw Gear Puller, Removal Tool for Gears, Pulleys, Bearings and Flywheels, Fully Assembled, CR-V Steel

  • Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
  • Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
  • Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
  • Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas..
  • Jaw Spread: 8in, Jaw Reach: 9-1/16in, Puller: 12T. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free replacement insures your DURATECH Wrenches purchase against manufacturer defects..
Check Stock

DURATECH 6-Inch 3-Jaw Gear Puller, Removal Tool for Gears, Pulleys, Bearings and Flywheels, Fully Assembled, CR-V Steel

  • Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
  • Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
  • Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
  • Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas..
  • Jaw Spread: 6in, Jaw Reach: 2-9/16in, Puller: 5.7T. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free replacement insures your DURATECH Wrenches purchase against manufacturer defects..
Check Stock

Upper & Lower Bearing Carrier Puller with Fuel Water Separator Wrench for Yamaha, for Johnson, for Evinrude, for Mercury, for Honda

  • APPLICATION -- All fit for Yamaha. ①Upper Bearing Carrier Puller - Fit For Yamaha, Johnson, Evinrude, Suzuki, for Honda and Mercury upper bearing carrier (NOTE: with carrier style upper bearing housing)②Lower Bearing Carrier Puller - Fits For Yamaha, Johnson, Evinrude, Mercury (DOES NOT FIT VERADO), for Honda, Mercruiser.③Wrench - Fit For Yamaha Outboard Motors 2006 Serial Number 0406 To Current. Fits Yamaha 4-Strokes 150 to 350 HP, HDPI 2006+.
  • FUNCTION -- ①Puller works wonderfully for removing the bearing carrier oil seal and other tasks where a bearing puller is needed.②Wrench is specially designed to remove fuel water separator cup..
  • BENEFITS -- ①Save time and No more prying against seal surfaces. Removes toughest Lower bearing carriers effortlessly with no damage to the carriers.②Safely removes fuel water separator cup from filter assembly without damaging delicate plastic parts and avoids tangling in the water sensor wiring..
  • ADJUSTABLE -- Fits most gearcases 115hp and above. Adjustable arms allows it to be used on a variety of different sized outboard and outdrive / stern drive lower units..
  • SATISFACTION GUARANTEE -- If you are not satisfied with Camoo products, simply return it for a full refund in 30 days. Guarantee with 12 mon....
Check Stock

GXL Carrier Pinion Bearing Puller for Dana 30, 40, 60, 70, Ford 9'' inch Clamshell Design.

  • Double heat treated for extreme strength.
  • Bearing Puller with durable steel and Works with impact Gun for easy and safe use..
  • Small(yellow) and Medium(Black) Clamshells with Bearing Puller Tool Stand and One Screw Assembly..
Check Stock

KUNTEC 3 Jaw Inner Bearing Puller Heavy Duty Pilot Sleeve Gear Extractor Internal External Pulling for Motorcycle Wheel Car SUV

  • 【Strong Material】3-Jaw Inner Bearing Puller Tool is constructed from carbon steel, the overall heat treatment, strong and durable. Corrosion-Resistant black oxide finish, preventing damage to bearings..
  • 【Well Equipped】3 Jaw Inner Bearing Puller removes bearings, pump bearings, bushings, removes all sleeve type bearings with 1/2"-2" inside diameter.
  • 【Advantage】The three-jaw design can apply pressure evenly to prevent damage to the bearing and ensure stability during use. There are two installation methods for the claw foot..
  • 【Labor Saving】Structure design, gently turning the small wrench can produce a strong pull force.
  • 【Wide Application】3 Jaw Bearing Puller is designed for automotive flywheel, motorcycle wheel, bicycle wheel, pump bearing, generator bearing, machine bearing etc.
Check Stock

VEVOR Carrier & Pinion Bearing Puller Compatible with Dana 30,40,50,60,70, 80, Ford 10.25  Bearings Pinion Puller Tool with 3 Clamshells 45# Steel Clamshell Bearing Puller for Auto Repair

  • Great Compatibility: The clamshell carrier bearing puller is compatible with Dana 30, 40, 60, 70, Ford 10.25" bearings. With the clamshell bearing puller, you can quickly remove the bearings. In addition, its power is evenly distributed, so less damage will be brought to your pinion bearings..
  • Premium Performance & Features: With high working efficiency, this carrier pinion bearing puller can effortlessly remove the pinion bearings with minor damage, drastically reducing dismantled time. And the carrier bearing puller will no longer easily pry into the pinion's sealing surface..
  • Complete Equipment: All necessary parts are ready for you. There is a main puller body, plug, center bolt, 3 clamshells, retaining ring, and adjuster rings. Besides, this unit comes with a handy stand, so you can group all the working parts together..
  • Easy to Operate: There is no need for other complex working tools. Firstly, place the main body over the plug and adjust the lower and upper adjusting ring. Secondly, select a proper clamshell and tighten the retaining ring. Finally, you can use an impact gun to remove the bearing..
  • Superior Material: The clamshell bearing tool is made of durable 45# steel, providing good performance in withstanding abrasion, corrosion, and impa....
Check Stock

Bonvoisin 5T Hydraulic Gear Puller Set Wheel Bearing Puller Kit 2 or 3 Jaws Pulling Separator for Wheel Hubs Rotors Car Axles Pulleys Brake Drums

  • Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
  • Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
  • Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
  • Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas..
  • Jaw Spread: 8in, Jaw Reach: 9-1/16in, Puller: 12T. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free replacement insures your DURATECH Wrenches purchase against manufacturer defects..
Check Stock