ReviewsPicatinny Scope Rings

Monstrum Pro Series 7075 Aluminum Scope Rings | 30 mm | Medium Profile

Monstrum Pro Series scope rings are crafted from 7075 aerospace aluminum - providing greater tensile strength, shear strength, and Brinell hardness than typical 6061 aluminum scope rings.
Comes with stainless steel Torx mounting hardware, including a T25 Torx Plus wrench and a T25 Torx Plus Bit, for easy precision mounting without stripping of bolts.
Pro Series scope rings are treated with a Type III Hard Anodized Finish versus a Type II for previous generation scope rings for added protection against scratches and blemishing.
Available in 1 inch or 30 mm diameter. Compatible with both Picatinny or Weaver mounting bases..
All Monstrum products are now protected by Monstrum’s lifetime guarantee.

Monstrum Pro Series scope rings are crafted from 7075 aerospace aluminum – providing greater tensile strength, shear strength, and Brinell hardness than typical 6061 aluminum scope rings.
Comes with stainless steel Torx mounting hardware, including a T25 Torx Plus wrench and a T25 Torx Plus Bit, for easy precision mounting without stripping of bolts.
Pro Series scope rings are treated with a Type III Hard Anodized Finish versus a Type II for previous generation scope rings for added protection against scratches and blemishing.
Available in 1 inch or 30 mm diameter. Compatible with both Picatinny or Weaver mounting bases..
All Monstrum products are now protected by Monstrum’s lifetime guarantee.

... reticle adjustment. Dependable waterproof (IPX-7 rated for complete immersion up to 1 meter) and fog-proof performance..
PRECISION Line up your shot at the exact height you want it with the Monstrum Tactical Precision Scope Rings! 1 inch in diameter, the rings are built for use with standard 1 inch scope tubes. The Picatinny base is compatible with all Picatinny mounting systems..
INCREASES STRENGTH It is not compatible with Weaver mounts. The torx locking screw system allows for quick yet powerful tightening while protecting the screws from stripping. These scope rings also features 2 square-integral recoil stops on each ring, which allows us to shave down the weight, while increasing the strength..
NO COMPROMISING Now you do not have to compromise when it comes to choosing either versatility or precision. The Monstrum Precision Rings allow you to properly align your scope to your rifle so you have one less thing to worry about..

The double tactical low profile scope mount fit for 1 inch / 25.4mm scope tube on the picatinny/weaver rails..
The height from the center of the riflescope tube to the picatinny base is 0.74 inches (18.7 mm)..
With mountings screws on the base and four screws on each side of the two scope rings. It will hold the riflescope mount securely..
Precision machined from aluminum alloy with anodized black matte finish. Light weight, only 2.46oz/70g..
Easy to install. Note: the rings have a star nut for installation rather than a hex nut and the tool is included..

Please note that as of 9/2021, Savage Arms has altered the drill hole pattern on newly manufactured Savage Axis rifles. Check the serial number on....
Picatinny rail mount built specifically for Savage Axis/Axis II/Edge rifle platforms.
Allows for the mounting of Picatinny or Weaver standard scope rings, scope mounts, red dots, or other optics.
Available in two styles - a 0 MOA mount for zeroing your scope at short to mid range distances and a 20 MOA mount for zeroing your scope at long....
All Monstrum scope mounts and accessories come with a lifetime guarantee.

Double 1'' scope ring mount for Picatinny/ Weaver Rail (21mm)..
Design in hollowed-out configuration between the ring and the bottom of the base, to release heavy duty when clamping your scope..
Built-in tape inside per rings to prevent from marring the scope, also prevent sliding and holding postion accurately..
The ring is for most scopes which are in 1''/ 25.4mm scope tube. High profile, 0.98'' gap from base of mount to bottom of rings. ( Item height: 2.1'').
With only 1 rail clamp screw and 1 scope clamp screw per side, just twist off the nut and mount the base on the 20mm rail easily..

Picatinny/Weaver rail mount built specifically for Marlin 336/1894/1895 Series lever action rifles.
Scope mount installs directly to receiver via the factory mounting holes and included set screws with no additional hardware required.
Allows for the mounting of Picatinny or Weaver standard scope rings, scope mounts, red dots, or other optics.
Integrated level bubble built into the rear of the rail to check for consistent vertical alignment of your rifle.
All Monstrum scope mounts and accessories come with a lifetime guarantee.

Adjustable 4-12 times magnification, for targeting out to 600 yards and beyond.
An adjustable objective lens or AO - that allows for sharper focus of the target image, elimination of parallax, and range estimation.
Aircraft grade 6061 aluminum scope body with a sealed, nitrogen-charged tube for resistance to water and fog.
Precision 1/4 MOA/click windage and elevation adjustments with locking turrets.
Available with High Profile Picatinny/Weaver Scope Rings or with an Offset Picatinny Scope Mount.

Fits on any Weaver or Picatinny-style mount.
Ideal for tactical use/Also great for hunting rifles, slug guns, and muzzleloaders.
Optional Picatinny rail on top of ring allows for attachment of accessories on top of a mounted scope.

Built specifically for long range scopes - 6-24x magnification scopes and above - with 3 inches of spacing between scope rings to accommodate scopes....
Lightweight one-piece scope mount for mounting standard 1 inch diameter tube rifle scopes - with weight comparable to a set of lightweight rings,....
Mounts to any flat top Picatinny rail equipped rifle with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle....
2 inches of forward extension allows extra flexibility for optimum eye relief and shooting position.
Mount frame crafted from lightweight 6061 grade aluminum with hardened steel Torx mounting hardware to prevent stripping of the bolts.

1.35 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
34 mm diameter rings for mounting standard 34 mm rifle scope tubes.
Picatinny mount base mechanism comes equipped with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil | Not compatible with Weaver mounts.
Uses hardened steel Torx mounting hardware to prevent stripping of the bolts.
Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.