ReviewsPillow Stock Bearing

NEW RAM HYDRAULIC THROWOUT BEARING FOR FORD TOPLOADER TRANSMISSIONS & STOCK C.

Brand New Ram Hydraulic Throwout Bearing Kit (Ram Part #78136)..
Works with Ford Toploader Transmissions that have a bearing retainer collar with an outside diameter of 1.375" or less, as the inside diameter of this throwout bearing is 1.380" * Toploaders either have an 1 1/16"-10 spline or 1 3/8"-10 spline input shaft.
This bearing isn't big enough to work with the 1 3/8"-10 version. * In addition, some toploaders with an 1 1/16"-10 spline shaft have a larger retainer, so it's a good idea to measure the retainer collar to make sure it is 1.375" or less..
Includes a set of conical shims to properly fit the bearing, installation stud, inlet, outlet, and conversion fittings, as well as a remote bleeder line..

Made of bearing steel and cast iron shell, high hardness and durable..
Pillow block bearing is a kind of bearing unit which combines rolling bearing and bearing block, which has good versatility and interchangeability..
Two-bolt housing with ball bearing insert for ready-to-mount installation..

3 Pice Zebra Print 1500 Series Bed Sheet Set.
1 Flat Sheet, 1 Fitted Sheet and 1 Standard Pillow Case ( Note: the stock photo show 2 pillow cases but this Twin set will come with 1 Pillow case).
Microfiber 1500 series super soft sheets..
Easy care sheets are machine washable. Wrinkle Free.

☘️【Material】Our stainless steel adopt high quality stainless steel, this lead screw is rust and corrosive resistant, durable and stable..
☘️【Smooth Movement】It has low friction that helps the nut move smoothly on the lead screw. It also helps the lead screw work precise and accurate..
☘️【T8 Brass Nut】 There are 4 holes on the T8 brass nut which can easy to fix to the machine..
☘️【Bearing Pillow Block】Bearing Pillow Block have a certain bearing capacity, can hold in ordinary precision rack, strong adaptability, and widely applied..
☘️【Widely Usage】 T8 lead screw can cover a wide usage in 3D printer, stepper motor and CNC 3D engraving machine and other DIY kit..

Brand New Ram Hydraulic Throwout Bearing Kit for Stock Style Clutches with GM Tremec T-56 Transmissions (Ram Part #78165)..
Fits GM Tremec T-56 transmissions in: * 1997-2004 Chevy Corvette with LS1, LS6, and LS7 engines. * 1998-2002 Chevy Camaro with LS1 engines. * 1998-2002 Pontiac Firebird with LS1 engines..
Fits stock style clutches. * Includes a replacement transmission collar to install on your T-56..
Includes a remote bleeder line, as well as a supply line. The factory supply line is cut and the adapter fitting (included) is installed with the new supply line..
Also, includes a set of conical shims to properly fit the bearing, installation stud, inlet, outlet, and conversion fittings, as well as installation instructions..

Please verify your year, make and model in the product details before purchasing..
OEM Replacement. Brand New Complete Rear Wheel Axle and Bearing Carrier.
Stock Length rear wheel axle & bearing carrier.
This axle is an OEM replacement for the following OEM # 5LP-25381-10-00 / This bearing carrier is an OEM replacement for the following OEM # 5LP-25311-10-00.

Upgrade with the sized .80 A/R compressor housing and the larger 63.5mm billet compressor wheel which flows more air compare to the stock turbo.
The kit comes with the 360º thrust bearing handles more thrust force over the stock 270º one, both seal rings have staggered step gap which reduce oil from leaking out.
The kit is designed to fit all stock 6.0 turbos, will the help of the hardwares in the kit, you can install it easily..
Fits turbo model: Garrett VGT GT3782VAS Turbo.

Brian Tooley LS Rocker Arm Upgrade Trunion Kit Includes Allen Head Bolts.
These LS Series retrofit trunion kits are designed to convert stock LS Series rocker arms into captured roller bearing rocker arms. The factory bearings are a known failure on the LS Engines. When they fail they send small bearings through the entire engine. The upgraded trunions use a captured roller bearing allowing for a reliable smooth rotation..
The upgraded trunions also give more stability at higher RPM. We use these trunion kits in anything from stock 4.8's all they way up to 1,000+hp turbo motors.The stock factory LS rocker arms are very strong and very light. Once you upgrade the bearings and trunions the rocker arms handle similar to very expensive roller rocker arms (at a fraction of the cost)..
These are a must have for anyone installing a aftermarket Cam, Supercharger, Turbo or Nitrous..
Used on all LS style rocker arms including the following: LS1 LS2 LS3 LS6 L99, LS4, LS9 LSA LQ4 LQ9 L76 L92 LR4 LM7 L59 LM4 L33 L98 L77 LY6 LFA LZ1 LY2 L20 LMF LH6 LY5 LMG LC9 LH8 LS4 4.8 5.3 5.7 6.0 6.2.

... by keep them away from the blade or cutter.The Thin Rip works much like a feather except that it doesn’t exert spring like pressure against the board. This means it can be used to make accurate, repetitive cuts since it’s essentially just holding its spot once it is secured..
The Thin Rip Jig has a roller guide bearing on the tip to make feeding your stock through an easy and smooth moving process. The free rotating bearing is made from high quality materials for extended workshop use. The jig fits directly into most any standard 3/8” x 3/4” miter slot. The body is made from a solid piece of aluminum and is adjustable inward and outward from your fence depending on the width of your stock..
The jig can be used on other workshop machinery like router tables with fences and band saws for re-saw applications. In certain cases, when working with larger or longer stock on table saws or router tables, we recommend using two thin rip jigs behind the blade or cutter for extra stability when feeding your stock through..