ReviewsPressure Tube

10 x 2.125 (10 Inch) Inner Tube for 2-Wheel Scooter fit 10X2 Tires 10X1.90 10X1.95 10X2 10X2.125 Inner Tube 2 Pack of

Size: 10 x 2.125 (10 Inch) .Recommended Charged Pressure: PSI 36 (Please note that you‘d better inflate according to the recommended charged pressure of the inner tube. Do not inflate according to the pressure marked on the tyre, otherwise the tire will burst easily)..
This inner tube fit 10 inches, not fit 6.5 in or 8 in ones.
Material : Isobutylene Isoprene Rubber which is better in air tightness, elastic damping and aging resistance than natural rubber..
Also fit 10X2 Tires 10X1.90 10X1.95 10X2 10X2.125 Inner Tube.

Package includes pump, thermal relief valve, and detergent tube with filter.
Horizontal plunger pump runs at 2.5 GPM at 3,000 PSI and spins at 3,400 RPM.
3-piston alternating volumetric pumps for use on cleaning units.
Thermal relief valve is mounted into the low pressure side of the pump manifold and will vent heat. Shaft direction: Standard..
Detergent tube can be used for pressure washer pumps, misting pumps, and Blue Clean pressure washing equipment. Start style: EZ Start.

【50 ft x 1/4 in Universal Hose】This paint sprayer hose is compatible with sprayers, it supports most mainstream airless sprayer brands, easy to use while spraying under pressure. Suitable for most common architectural paints and solvent-based coatings..
【Hose Material】The airless paint sprayer hose is made of four layers of high-quality materials. The first layer is the nylon inner tube layer, the second is the fiber braid layer, the third is the steel wire braid layer, and the outermost is the PU wear layer. Can withstand aging, high pressure, corrosion, and anti-burst. More durable than other brands..
【Bending Performance】The airless paint sprayer hose has good flexibility and easy bending. The tube body is tightly combined, which improves the usability of spray under pressure..
【Durability】The paint sprayer hose is 50ft long, extending the reach of your sprayer for peaks or second stories without diminishing performance. The tube is light and easy to carry, with low fluid resistance and small volume expansion, which does not affect the working pressure..

Bulkhead Fitting Push Connector Type : 3/8 inch, Tube OD 3/8 inch NPT.
Bulkhead Fitting Type: Push In Straight Male Connector.
Body:Nickel Plated Brass Seal, O-Ring NBR.
Bulkhead Fitting Features: high pressure resistant and non tripping, all taper pipe threads are paint Teflon leakage-proof rubber, offering good seal property.
Push Fittings are easy to install, flexible and space-saving, 360-degree rotate freely, Release rings adopt ellipse design, which can be removed conveniently.
Fluid Admitted: Air, Vacuum, Water (No Freezing).
Negative Pressure-100Kpa | -29.5 In Hg. Working Temperature: 0-60¡ãC | 32¡«140¡ãF. Applicable Tube:PU / PA / PE / PVC.

Body Style: Male Straight / Size:1/2” Tube OD x 1/2“ NPT thread Straight push in connect fitting.
Working Pressure:0-1.0MPa | 0-150psi/Applicable Tube:PU / PA / PE / PVC.
Working Pressure:1.0Mpa | 145psi.Seal O-ring:NBR.
Working Temperature:0-60°C | 32～140°F ；Negative Pressure:-100Kpa | -29.5 In Hg.

Body Style: Male Straight / Size:3/8” Tube OD x 1/4“ NPT thread Straight push in connect fitting.
Working Pressure:0-1.0MPa | 0-150psi/Applicable Tube:PU / PA / PE / PVC.
Working Pressure:1.0Mpa | 145psi.Seal O-ring:NBR.
Working Temperature:0-60°C | 32～140°F ；Negative Pressure:-100Kpa | -29.5 In Hg.

Gauge has a full geared, precision movement with bronze bourdon tube.
unlike piston-plunger-type gauges, the bourdon tube movement is not affected by....
Swivel angle chuck makes it easier to reach tire valves.
Durable steel case with polished brass bezel, stem, pressure release valve assembly and a 2 inch dial.
5-60 PSI steel case gauge (recommended for tire pressures 15-45 PSI).
Needle holds pressure reading until released and a pushbutton valve bleeds air to desired tire pressure.

Gauge has a full geared, precision movement with bronze bourdon tube.
unlike piston-plunger-type gauges, the bourdon tube movement is not affected by....
Swivel angle chuck makes it easier to reach tire valves.
Durable steel case with polished brass bezel, stem, pressure release valve assembly and a 2 inch dial.
3-15 PSI steel case gauge (recommended for tire pressures 5-12 PSI).
Needle holds pressure reading until released and a pushbutton valve bleeds air to desired tire pressure.

Gauge has a full geared, precision movement with bronze bourdon tube.
unlike piston-plunger-type gauges, the bourdon tube movement is not affected by....
Right angle chuck with flexible 11 inch hose between gauge and chuck for hard to reach tire valves.
Durable steel case with polished brass bezel, stem, pressure release valve assembly and a 2 inch dial.
5-30 PSI steel case gauge (recommended for tire pressures 8-23 PSI).
Needle holds pressure reading until released and a pushbutton valve bleeds air to desired tire pressure.