ReviewsPu Shaft Coupling

uxcell 8mm Inner Dia H13*D16 Rigid Flange Coupling Motor Guide Shaft Coupler Motor Connector 2PCS for DIY Parts

  • Inner Diameter: 8mm/0.31 inch, Total Height: 13mm/0.51 inch, Cylinder Outer Diameter: 16mm/0.63 inch, Cylinder Height: 10mm/1.31 inch, Base Diameter: 32mm/1.26 inch, Base Height: 3mm/0.12 inch, Mounting Hole Distance: 24mm/0.94 inch,2 x M4 Fastening Screws.
  • Type: Flange Shaft Coupling, suitable for model shaft connection, perfect accessories for RC Model motor, etc..
  • Material: Aluminum Alloy, hardened by heat treatment, and then electroplated. Durable and insulation, make your shaft more stable, easy to install and replace..
  • Function: A special coupler, which can fix one shaft to a plane and install other parts on the shaft easily. Double connection points fasten the coupler tightly..
  • Package: 2 x 8mm Flange Shaft Coupling, 4 x Fastening Screw( M4 Hex Wrench Not Included Here ).
Check Stock

uxcell 10mm to 12mm Shaft Coupling 30mm Length 25mm Diameter Stepper Motor Coupler Aluminum Alloy Joint Connector for 3D Printer CNC Machine DIY Encoder

  • Shaft Usage: 10mm to 12mm / 0.39 to 0.47 inch.
  • Flexibility of coupling shaft removes stress between the motor and driving components..
  • The shaft couplers are widely applied to small CNC machines encoding and 3D printers Z shaft coupling, simplifies the debugging difficulty..
Check Stock

4 Pack 8mm Flange Coupling Connector, Rigid Guide Steel Model Coupler Accessory, Shaft Axis Fittings for DIY RC Model Motors, High Hardness Coupling Connector-Silver.

  • 【Durable Material】 Ancirs coupling connector is made of fine plating steel, heat and electroplated process make it sturdiness and insulation, striking shaft more stable and easy for installment and replacement..
  • 【Wide Range of Use】Ancirs flange coupler is produced based on International Flange Standard, widely used in model shaft connection, perfect accessories for RC Model motor..
  • 【High cost performance】Ancirs flange coupler is packaged with 4 pack 8mm Flange Shaft Coupling + 4x M3 Mini Hex Wrench + 8 x M3 Fastening Screw..
  • 【Standard Specification】Inner Diameter: 8mm. Cylinder Outer Diameter: 10mm. Cylinder Height: 10mm. Base Diameter: 22mm. Base Height: 2mm..
  • 【100% Satisfaction Guarantee】 If you are not completely satisfied with ANCIRS Flange Coupling Connector, just contact us through Amazon message and we will provide feasible solution for you as promised..
Check Stock

Xnrtop 8mm to 8mm Shaft Coupling 25mm Length 18mm Diameter Stepper Motor Coupler Aluminum Alloy Joint Connector for 3D Printer CNC Machine DIY Encoder(Pack of 2)

  • Shaft Usage: 8mm to 8mm / 0.31 to 0.31 inch.
  • Flexibility of coupling shaft removes stress between the motor and driving components..
  • The shaft couplers are widely applied to small CNC machines encoding and 3D printers Z shaft coupling, simplifies the debugging difficulty..
Check Stock

Universal Joint, 16mm to 32mm Rotatable Universal Joint Shaft Coupling Metal Motor Connector Coupler with Screws for RC Boat Car

  • 【HIGH QUALITY PRODUCT】1 Pc universal joint coupling with 2 Pcs screws, brand new and high quality, practical and reliable, easy to install and remove..
  • 【PERFECT MOTOR SHAFT FITTING】360 degree rotatable, it is commonly used for shafts that transmit rotary motion, perfect motor shaft fitting accessories..
  • 【OUTSTANDING COUPLING CONNECTOR】This joint or coupling connects rigid rods whose axes are inclined to each other, outstanding appearance and performance..
  • 【METAL MATERIAL】Made of premium metal material, it is durable and has long service life..
  • 【WIDE APPLICATION】Widely applied for connecting model cars, model ships, robots, etc..
Check Stock

uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L22XD16 45# Steel,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 10mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 8mm to 8mm Bore Rigid Coupling Set Screw L22XD14 45# steel,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 8mm to 8mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 7mm to 7mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories

  • Total Length: 22mm/0.87 inch, Outside Diameter : 14mm/0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 4mm to 4mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 4mm to 4mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 5mm to 6mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories,2pcs

  • Connection Diameter: 5mm to 6mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 1/8 inch to 5mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 1/8 inch to 5mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock