ReviewsPwm Servo Board

15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.

PWM voltage converter Convert 0-100% PWM digital signal into analog signal..
Signal interface switching between single chip or other industrial control board..
The power supply has the function of reverse connect protection, safe to use ..
Input digital signal can be 24V level 0-100%PWM signal. Output analog signal can be 0-10V voltage..
PWM signal receiving frequency range: 100hz-3khz, recommended 1khz-3khz..

5V isolate with MCU, and effectively protect MCU.
Voltage indication of motor driver output end.
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2).
isolation chip 5 V power supply (can share with MCU 5 V)..
Able to reverse the motor forward, two PWM input frequency up to 25kHZ.
two heat flow passing through an error signal output..
Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply.

10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
Great for jumping from board to board or just about anything else..
There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
Length:100mm Type:JR Plug Servo Extension wire (Male to Male).

...SD, or as a high-speed mass storage device as a media library for NAS or Volumio..
Integrated with CH340E chip and DB9 male header, RS232 or RS485 function can be selected by DIP switch. The TXD/RXD signal has LED indicators to show the communication process of sending and receiving. Can be connected to PLC, stepper/servo drive, LORA module....
The display is equipped with 2 damping shaft brackets, the display angle can be adjusted arbitrarily, and the brackets can also be removed to install the case. The STL file for the 3D printed case is available under eleclab-rpi/7INCH_DSI_DISPLAY, and the fan case STL file is under eleclab-rpi/rpi_fan_case..

（pack of 6 ）This D1 mini module is a mini WIFI board based on ESP-8266EX..
Our D1 mini development board is 100% compatible with Arduino WeMos and can be programmed in Compatible with Arduino IDE..
Support OTA on line.Compatible withArduino compatibility. Using Compatible with Arduino IDE for programming..
This WLAN board contains 11 digital input / output pins, all pins have interrupt / pwm / I2C / 1-wire and a micro-USB connection..
11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
1 analog input(3.2V max input). Micro USB connection.

Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
This servo Y-cable allows you to control two servos with one radio channel..
Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..

♞【Model】Upgraded 3 Axis GRBL 1.1F USB Port GRBL Control Board.
♞【Support software】GRBL Contol/Candle(3 axis)/Universal Gcode Sender.
♞【Support Motor】Support XYZ three-axis control, spindle.Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor Nema17,Nema23).
Support spindle: Support 24VDC Spindle PWM speed (0%-100%),also support 3-pin PWM/TTL signal control module.
♞【New functions】Add 2-pin emergency stop button port,probe port,XYZ limit port and add the power button switch..
♞【Applications】 The control board can be used with the 1310,1610-PRO, 3018,3018-PRO and 3018-PRO MAX etc engraving machines..

Compatible with Raspberry Pi 4 Model B --- This Armor Lite Aluminum Heatsink is only designed for Raspberry Pi 4 Model B 1GB/2GB/4GB/8GB Version..
Support PWM Speed Control --- Different from ordinary fans, this cooling fan supports PWM speed regulation, which is perfectly compatible with Raspberry Pi OS..
Good Heat Dissipation Effect --- With 3510 ultra-quiet cooling fan and thermal pads, it can lower the temperature of Raspberry Pi Board quickly..
Lightweight and Easy to Install --- With screwdriver and 2pcs screws, it's easy to fix the heatsinks with Raspberry Pi Board..

1️⃣ 7-80V PWM DC Motor Speed Controller Switch 30A,Motor Speed Control Regulator.
2️⃣ Wide voltage 7-80V high current 30A Design Wide range of applications, on-board switch with operation Stop brake function, adjustable potentiometer soft cable can be separated Line length 30CM..
3️⃣Circuit optimization design Wide range of duty cycle adjustment, smooth motor without vibration, no vibration, with power indication, stable circuit design for long working hours..
4️⃣Adopt imported high-voltage MOS tube, three high-voltage 100V high-frequency resistance capacitors, and fuses for braking. The parameters are not easy to heat and easy to replace. The standard aluminum housing protects the internal circuits and components for long-term durability..
5️⃣Package Contents:1 x 7-80V PWM DC Motor Speed Controller Switch 30A.
Amazon satisfied customer service & fast ship..

This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
Includes a total of over 190 electronic parts and components.