ReviewsRaspberry Pi Audio

Waveshare Overall Evaluation Board Designed for Raspberry Pi Pico Misc Onboard Components for Easily Evaluating The RP2040

Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards. 3.5inch resistive touch screen, 65K colorful, bringing clear and vivid display effect.
Standard 3.5mm audio jack, for headphone or other audio peripherals. Micro SD card slot through the SDIO interface, faster access speed than SPI interface.
Integrates battery header and recharge circuit, allows it keep running without wired power supply.
Other rich resources like buzzer, photoresistor, and RGB LED....
Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples).

Check Stock

RPI HiFi AMP HAT TAS5713 Amplifier Audio Module 25W Class-D Power Sound Card Expansion Board for Raspberry Pi 4 3 B+ Pi Zero Nichicon Capacitor

The HiFi AMP Hat compatible with Raspberry Pi 4, Zero, Zero W, 3B, 3B+ through the 40-pin connector. Connects directly to the Raspberry Pi board, no additional cables required, no soldering required. Easy to get more beautiful and fantastic sound by this RPI+AMP HIFI suits..
Absolutely perfect to support all Raspberry Pi music player system, such as OSMC, Max2Play, RuneAudio, Volumio, Moode, Pi CorePlayer, Pi MusicBox, OpenELEC, Debian, Ubuntu etc. Support playing music from a hard disk or over the network. Support DSD over PCM(DOP) mode..
On-board TAS5713 is a 25-W Class-D digital-audio power amplifier for driving stereo bridge-tied speakers. Offers low distortion and acoustically accurate audio reproduction..
Accept a wide range of input data 8-Khz to 48-Khz, Up to 90% Efficient, Supports speakers 4 Ohm impedance allows you to enjoy high quality audio..
Comes with software, document and friendly technology support. For more information please refer to our wiki（view the link on color page comes with the goods)..

Check Stock

RETROFLAG NESPi 4 CASE, Raspberry Pi 4 Case with SSD CASE, HDMI Cable & Cooling Fan & Heatsinks for Raspberry Pi 4 Model/Pi 4B (Pi 4 Case)

【Compatible With】 Retroflag NESPi 4 CASE is upgraded version, specifically designed for Raspberry Pi 4 Model B, NOT compatible with other Raspberry Pi model. The old version uses large fan for cooling, it is affect the operation of the case..
【Safe Shutdown and Reset】 This is NESPi 4 CASE version with Safe Shutdown and Safe Reset function. It will be more safe for your SD card when shutdown and reset..
【Easy to Assemble & Access】 NESPi4 CASE offers your Raspberry pi good protection with ONLY few steps to assemble, you can access to all ports of Raspberry Pi 4 Model B computer, such as power, audio, USB, LAN, MicroSD Card Storage, and Micro HDMI connector without opening the CASE. Also this NESPi 4 Case comes with NES Cartridge style case for 2.5'' SSD, easy to install your SSD, enjoy an overall better computer experience!.
【NES Style】We created this RETROFLAG Pi 4 case applying the most iconic element in the retro game world as a homage to the most classic console ever made, this NesPi 4 case can make your Raspberry Pi 4B become a NES retro gaming machine in one second!.
【Strong Heat Dissipation】RETROFLAG Pi 4 Case is equipped with a quiet cooling fan and 2 heatsink with better heat dissipation, could prevent system failure and Raspbe....

Check Stock

4.3inch HDMI LCD 800x480 IPS Capacitive Touch Screen HDMI Interface Support All Version Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH,Jetson Nano BB Black Banana Pi Windows 10/8.1/8/7

4.3inch HDMI LCD (B),IPS screen,Capacitive Touch Screen LCD.HDMI interface, 800x480 hardware resolution, configurable by software (up to 1920x1080),Supports Multi mini-PCs, Multi Systems.
Supports popular mini PCs such as Raspberry Pi，All Version of Raspberry Pi(4B/3B+/3B/2B/Zero/Zero W/Zero WH), When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free. Note: when it connects with Raspberry PI Zero/Zero W/Zero WH,Mini HDMI Converter Adapter and USB Converter Adapter should buy separately..
Supports Jetson Nano, BB Black, Banana Pi, as well as general desktop computers,When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free.
Supports popular game consoles like Microsoft XBOX360,etc..
Multi languages OSD menu, for power management, brightness/contrast adjustment, etc. 3.5mm audio jack, speaker connector, supports HDMI audio output..

Check Stock

YaFex Case for Raspberry Pi 4 B with Cooling Fan and Fan Guard,4 Pcs Heat Sinks,5V 3A USB-C Power Supply, USB Card Reader,1.5M Micro HDMI Cable and HDMI Adapter

【Latest Version Raspberry Pi 4 Case】Unique 9 layer raspberry pi case designed for Raspberry Pi 4 Model B. Made of acrylic, the Raspberry Pi 4B case won’t block Pi’s Wifi or Bluetooth signal..
【Easy to Access to All Ports】Cut-outs for the dual micro HDMI, Audio/Video, USB and Ethernet ports, as well as the USB-C power connector and access to the micro SD card..
【Keep Raspberry Pi 4 Board Cooling】Specially come with quiet cooling fan and 4 pcs heatsinks for CPU/ROM/RAM quick cooling.Also included a fan guard to protect the fan..
【1.5M Micro HDMI Cable and HDMI Adapter】1.5M Micro HDMI to HDMI Cable for Raspberry Pi 4. Up to 4K Resolution. Up to 60P (Frames/Second). CEC Support. Also come with a 1.5M Micro HDMI to HDMI Adapter Cable..
【Excellent Customer Service】If you have any questions about the case installation, please feel free to contact us. We will teach you to use our products within 24 hours..

Check Stock

GeeekPi Acrylic Case for Raspberry Pi 4 Model B & Raspberry pi 3 Model B+, Raspberry Pi Case with Cooling Fan and 7PCS Heatsinks for Raspberry Pi 4 Model B/Pi 3B+/ Pi 3B/ 2B (Clear)

2 pieces of transparent acrylic box parts: easy to assemble and provides full access to your Raspberry Pi.
High Quality Acrylic case with fan secures your model Raspberry Pi 3B/3B+/Raspberry Pi 4B.
More easily access to the board, power, RCA Video, Audio, USB, LAN (model B only), SD card and Light pipes.
Great heat dissipation performance.Comes with assembly screwdriver..
Package Includes:1x Acrylic Case with Cooling Fan, 1x Screwdriver, 3 x Heatsinks for Raspberry Pi 3B+/3B/2B, 4 x Heatsinks for Raspberry Pi 4B(Added on 2019.7.26).

Check Stock

Raspberry Pi Expansion Board Raspberry Pi HiFi DAC+ HD Audio PCM5122 24 bit Expansion Board for Raspberry Pi 3 Model B / 2B /B+/A+/ Raspberry Pi Zero W

With DAC All function PCM5122 chip and I2S Input, X920 DAC+ board is a perfect HiFi / DAC+ / HIFI / Full HD audio expansion board for Raspberry Pi 3....
After using X920 board, User can coordinate with the broadcast system (such as Volumio, RuneAudio, OSMC, XMBC(Kodi), MOODE etc.) to set up your own....
X920 is available with RCA, 3.5mm phone jack output connectors and built in IR receiver (Vishay TSOP34838).
Full HD audio up to 24 bit/192kHz playback and Class leading audio (112db SNR, and 93db THD) function, Integrated hardware volume control with TI's....
Powered by Raspberry Pi, no external power requirements, Conforms to the Raspberry Pi hardware attached on top (HAT) specification..

Check Stock

AURSINC SHARI PiHat - Portable SA818 Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4 | Raspberry Pi Hosted Allstar Node | UHF Frequency Range 1W 420-450MHz/70cm | Amateur Radio Operator

[What Is It] Small, portable with self contained radio and antenna, SHARI(SA818 Ham Allstar Radio Interface) is designed for construction and uses in the amateur radio service, works with a Pi2/Pi3 or Pi4, SHARI RF output power is 500 to 1000(default) milliwatts.
[Allstar Node] SHARI PiHatU implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz|70cm) radio module.
In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired) ；Note: only work with allstar node or any analog node.
[Power Supply] SA818 Ham Allstar Radio Interface is a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies..
[Feature 1] Front panel LEDs indicate the status of SHARI-POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red).
SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module.

Check Stock

Smraza Raspberry Pi 4 Touchscreen with Case, Cooling Fan, 4 inch Touch Screen IPS LCD Display 800x480 HDMI Monitor for RPI 4B 2GB/4GB/8GB with Touch Pen, Heatsinks(Support Raspbian Kali Octopi Ubuntu)

【4 inch HD Touchscreen】800x480 pixel hardware resolution, support HDMI input and HDMI audio output, backlight brightness adjustable. Resistive touch control, convenient human-computer interaction experience. 4 inch IPS full-angle display, refresh rate up to 60FPS. Support for playing video and games, while the picture is stable and clear can be used as a monitor screen, supporting 3.5mm stereo audio output..
【Cooling System】2 layers raspberry pi 4 touchscreen case especially designed for Raspberry Pi 4 and 4 inch touch screen. Come with cooling fan and 4 pcs heat sinks (size of heatsinks for CPU: 25 x 25 mm. ), it's better for heat dissipation..
【4inch display case for raspberry pi 4】4-inch touch screen monitor with an Acrylic case and related screw kits, you can choose to install it on a wall or stand to easily connect the monitor with Raspberry Pi or other devices..

Check Stock

ELECROW 8 Inch Touchscreen Monitor Portable Screen HDMI-Compatible LCD Display 1280x800 for PC Raspberry Pi Jetson Nano Game Consoles

【Touchscreen Monitor】ELECROW 8 inch touch screen monitor has an impressive feature of plug and plays that doesn’t require any driver installation, support 5 points touch max. This small portable monitor support HD 1280×800 resolution, IPS screen help keep colors consistent at a wide viewing angle..
【Portable Monitor】8 inch mini Raspberry pi touchscreen with a simple design, the size is only 195*121mm, and aluminum alloy shell makes this cctv monitor creates a nice look while keeping things compact and durable..
【Easy Connection】 The HD port of this small monitor is for audio/video transmission, works with HDMI-compatible devices like computer, laptop, Raspberry pi, Jetson Nano,and game consoles. This raspberry pi monitor is also a USB-powered monitor which can be powered by a power bank, PC, and wall plug. But please note that the touch function will only work when connect to USB port of signal output devices like laptop/pc/Raspberry Pi, but not power bank or wall plug..
【Support Speaker and VESA Install】This raspberry pi screen enhance your audiovisual experiences with built-in speakers. Volume/brightness can be adjusted. You can mount the portable screen on the wall via VESA or on the desk via the monitor stand..

Check Stock

10.1 Inch Raspberry Pi Touchscreen Monitor, 1280x800 IPS LCD Display with Built-in Dual Speakers, VESA Mountable, Compatible with Raspberry Pi 4B 3B+

7 INCH RASPBERRY PI TOUCHSCREEN: UPERFECT 7 inch raspberry pi touchscreen with case and fan and stand all in one machine has HDMI port for computer/ pc, Type C port for phone/ game, audio jack for headphone, DC 12V port for power. Which you could use as a normal monitor. This amazing monitor also has three side boards to choose. One for regular display, one for rpi 3 series, one for rpi 4 series..
PERFECT FOR DIY PROJECTS: This 7″ touchscreen monitor for Raspberry Pi gives users the ability to create all-in-one, integrated projects such as tablets, infotainment systems and embedded projects. Turn your Raspberry Pi into a touch screen tablet, infotainment system, or standalone device..
DO NOT NEED KEYBOARD AND MOUSE: Touchscreen drivers with support for 10-finger touch and an on-screen keyboard will be integrated into the latest UPERFECT Raspberry Pi touchscreen for full functionality without a physical keyboard or mouse. Truly interactive – the latest software drivers will support a virtual ‘on-screen’ keyboard, so there is no need to plug in a keyboard and mouse..
SIMPLIFY IoT & HOME AUTOMATION WORKFLOW: Make your own Internet of Things (IoT) devices including a visual display more convenient using UPERFECT rpi touchscreen all-in-one machine. S....

Check Stock