ReviewsReaming Finish

7/8\ Expansion Reamer, Carbide Tipped, Tapered Shank, 56067, USA Made

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Combination black and gold finish, for improved lubricity, corrosion resistance, and to reduce chipping or flaking.
These round shank tools have flats ground onto three sides to reduce slippage of the bit when used in drill chucks.
When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Construction reamer is especially adapted for heavy duty reaming as encountered in the fabrication of structural steel assemblies.

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
7/8 " shank diameter, For Reaming abrasive material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
3/4 " shank diameter, For Reaming abrasive material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

Ideal for reaming on stainless steel and copper tubing.
45 cutting edges on the interior cone allow for fast, clean inner reaming and outer deburring and beveling of tubes.
Hardened steel construction for maximum durability.
dual inch and metric measurement bar for ease of use.
Pipe reamer has a 1/2-inch to 2-inch (12 mm to 50 mm) outside diameter capacity.
RIDGID covers its products with a lifetime warranty against defects in material or workmanship for the life of the tool.

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
3/4 " shank diameter, For Reaming abrasive material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
Morse taper shank #3, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 1/2 " flute length, Partial Flute Length Carbide.
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 3/8 " flute length, Partial Flute Length Carbide.
Morse taper shank #2, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..