ReviewsRefrigerator Thermistor

Ametherm SL22 1R020 (Pack of 2) NTC THERMISTOR,ICL 1 OHM 20% 20A 22MM, (Also SG100, SG301)

Pack With: Package of 10pcs 1% accuracy 10K thermistor, 60mm / 2.4in line length..
High Sensitivity: The thermistor is high sensitivity and wide operating temperature range, which is easy to use..
Wide Use: Thermistor can be used as electronic circuit component for instrument line temperature compensation and temperature difference cold junction temperature compensation..
Small Size: The NTC thermistor is able to measure the gap temperature that other thermometers can't measure..
Good Stability: The thermistor has good stability and strong overload capability, easy to process into complex shapes..

M3 screw for installation is Quik and Durable, Flexible and Long Lasting, longer life span.
DIY players can also modify BLOCK by themselves. Make an M3 threaded hole in BLCOK, then you can use this thermistor.
Thermistor model: NTC 100K 3950. HERE is the firmware setting: *13:100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " &"Hotend "All In ONE"....
For the printer which uses NTC 100K 3950 thermistor, Then this thermistor is plug and use.

Compatible with all Polar N7, N8 and N10 refrigerator models.
4-prong connector that snaps into the light fixture at the light bracket.
Other end of the thermistor should be clipped onto the tenth fin from the right side.
Refer to manufacturer recommendations to ensure proper fit and usage.

Anet 3d printer 100k thermistor 1.2m can be used on both of the heated bed and the extruder for 3d printers.
The thermisor is compatible with most 3D printers in the market such as ender3, ender3 pro, ender3 V2, CR-10, hictop d3 hero eAnet 3d printer tc.
There is a 2 pin female connector on the thermistor for 3D printer.
Wire length for the thermistor: 1m/47 inches..
Recommended parameters for the thermistor: R25℃=100K.

The thermistor changes resistance as it senses the refrigerator temperature and sends a corresponding voltage to the pc board..
This product is covered under a 1 Year Warranty.

Direct replacement of cartridge type thermistor in E3D hotends..
A custom made thermistor encapsulated into an easy to use cartridge package..
Comes with (1) Hotend Thermistor with attached connector and (1) connector cable measuring 40 inches (101cm).

HICTOP 3d printer thermistor can be used on both of the heated bed and the extruder for 3d printers.
The thermisor is compatible with most 3D printers in the market such as ender3, ender3 pro, ender3 V2, CR-10, hictop d3 hero etc.
There is a 2 pin female connector on the thermistor for 3D printer.
Wire length for the thermistor: 1m/39.4 inches.
Recommended parameters for the thermistor: R25℃=100K B25/50=3950K± 1%.

003cb003ePrice For:003c/b003e Each 003cb003e Thermistor Type:003c/b003e NTC 003cb003e Resistance:003c/b003e 5ohm 003cb003e Thermistor Tolerance:003c/b003e -15% to +15% 003cb003e Thermistor Case Style:003c/b003e Radial Leaded 003cb003e No. of Pins:003c/b003e 2 003cb003e Dissipation Constant:003c/b003e 32.4mW/°C 003cb003e Leaded Process Compatible:003c/b003e Yes 003cb003e Mounting Type:003c/b003e Through Hole 003cb003eRoHS Compliant:003c/b003e Yes.

✅ PART NUMBER 8577274: The thermistor is a high-quality exact replacement for part numbers WP8577274, AP6013514, 8577274, 3390292, 3406294, 3976615, 772546, ER8577274, PS11746740, and WP8577274VP..
✅ FOR WHIRLPOOL DRYERS: Use the part to fix select Whirlpool, KitchenAid, Kenmore/Sears, and Maytag dryers. Check your dryer manual or reach out to us to confirm compatibility with your model..
✅ FIXES COMMON PROBLEMS: Dryer on the fritz? Replacing the thermistor, which regulates temperature in your dryer, can fix dryers that don’t produce enough heat, don’t start, or shut off too soon..
✅ SIMPLE DIY FIX: Remove a faulty thermistor and install this new one in under 20 minutes. Helpful tools include a 1/4-inch nut driver, a small flathead screwdriver, and a 1/4-inch socket and ratchet..
✅ HIGH-QUALITY PART: Designed to last, this thermistor meets or exceeds all original manufacturer specifications for performance and fit..

✅Package Includes: 1 x 279973 Thermal Fuse & Thermostat with Instruction Sheet, 1 x 3392519 Thermal Fuse, 1 x 8577274 Thermistor Control..
✅279973 Thermal Fuse & Thermostat – Dryer high limit thermal fuse and high limit thermostat kit. Includes instructions..
✅3392519 Thermal Fuse – Dryer non resettable thermal fuse, two 3/16″ wire terminals. This fuse is located on the blower housing next to the blower fan. If the dryer overheats, the thermal fuse blows to cut off power to the dryer and/or stop the dryer from running..
✅8577274 Thermistor Control – Dryer thermistor temperature sensor..
✅Replaces Part Number – Thermal Fuse & Thermostat 279973 3391913 3404151 3404152 3977395 8318314 897710 AP3094323 PS334387 EAP334387. Thermal Fuse 3392519 WP3392519 3388651 694511 80005 ET401 G4AP0500 3392519 PS11741460 AP6008325 2986 EAP11741460. Thermistor Control 8577274 WP8577274 3390292 3406294 3976615 772546 8577274 1181075 AP6013514 PS11746740 EAP11746740. the replacement part is a direct replacement for your dryer..
✅Buy with Confidence – Order from KONDUONE, you can return or exchange within 3 months, true worry-free shopping experience. If replacement part ever fails on your Dryer simply con....

003cb003ePrice For:003c/b003e Each 003cb003e Thermistor Type:003c/b003e NTC 003cb003e Resistance:003c/b003e 1ohm 003cb003e Thermistor Tolerance:003c/b003e -20% to +20% 003cb003e Thermistor Case Style:003c/b003e Radial Leaded 003cb003e No. of Pins:003c/b003e 2 003cb003e Dissipation Constant:003c/b003e 32.4mW/°C 003cb003e Leaded Process Compatible:003c/b003e Yes 003cb003e Mounting Type:003c/b003e Through Hole 003cb003eRoHS Compliant:003c/b003e Yes.