ReviewsRelay Connector

iztor Universal 6 Way Blade Fuse Holder Box with Spade Terminals Auto Electrical Connectors for car Truck Trailer and Boat

6-way fuse box 6-relay holder with spade terminals..
Suitable for all marine, motor-home, automotive & motorsport applications..
Waterproof connector.Can be installed in circuit..
Can be fixed through 2 pre moulded holes on side..
Package Includes:1 Piece Relay Holder Box and 32 Pieces Pins (Includes 4 different kinds )..

48Vdc, 17Adc Output, 120 Vac 60 Hz Input Golf Cart Charger.
Universal IEC Input Connector with A.C. Line ‘Power-Good’ and Disruption Green/Red L.E.D Indicator.
UL/CSA Listed BC Rated Replaces ASIN B00DHRFKX0.
Output Connector Type: EzGo RXV Triangle 3 pin Connector.

...ultaneously. A relay that completely isolated the 220 MHz RF filter won't impact the RF performance of the 2 meter/70 cm bands. If monitoring multiple 220MHz or VHF/UHF simultaneously the relay is not heard or used..
Tribander Mobile Radio Kit Includes: BTECH UV-25X4, Speaker Mic, 6 foot DC Cable with Cigarette Plug Connector, Radio & Mic Brackets, Mounting Hardware, and User Guide.

48Vdc, 17Adc Output, 120 Vac 60 Hz Input Golf Cart Charger.
Universal IEC Input Connector with A.C. Line ‘Power-Good’ and Disruption Green/Red L.E.D Indicator.
UL/CSA Listed Rated BC, 9 foot Input and Output cords.

The esp8266 module is 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
1 analog input(3.2V max input). Micro USB connection.
WiFi internet development board 5V 1A switching power supply (switching power supply）onboard..
5V relay shield is a digital switch to control much higher voltages and currents than esp8266 mini microcontroller, controlled by the D1 , the relay will switch to allow current to flow or turn off, depending on wiring..
40 pin 0.1inch (2.54mm) male pin header connector PCB board pin strip electronic component, they are easy to be cut to any length if needed, you can cut or score with some electronic tool..
The pin header is an ideal connector for the PCB board and intergrated circuit, used widely in the computer and breadboard, compatible with raspberry pi or other electronic project..

6-way fuse box 6-relay holder with spade terminals and 6pcs fuse, 5PCS 4Pin 12V 40A relays.
Suitable for all marine, motor-home, automotive & motorsport applications..
Waterproof connector.Can be installed in circuit..
Can be fixed through 2 pre moulded holes on side..
Package Includes:1 Piece Relay Holder Box and 41 Pieces Pins terminals..

...ultaneously. A relay that completely isolated the 220 MHz RF filter won't impact the RF performance of the 2 meter/70 cm bands. If monitoring multiple 220MHz or VHF/UHF simultaneously the relay is not heard or used..
Tribander Mobile Radio Kit Includes: BTECH UV-25X4, Speaker Mic, 6 foot DC Cable with Cigarette Plug Connector, Radio & Mic Brackets, Mounting Hardware, and User Guide.

Truck side repair connector and sockets for Western straight blade 6 pin controllers..
This is the truck side of the connector with sockets installed and 12" pigtails..
NOTE: This is for Western Straight Blade snow plows with either relay wiring, 3 port isolation module or 4 port isolation module. If your controller has four or ten pins, this will not work..

This harness is a 3 wire MAF and a 1 wire alternator. For drive by cable throttle body Only..
Compatible with LS1 4L60E 2003-2007 Chevrolet, GMC, Cadillac and Hummer engine.
suitable for 03-07 all using 4L60E(Vortec engine 4.8 5.3 6.0) gearbox automotive..
All wiring harnesses come with the required instrument panel connections, including speedometer, tachometer, neutral, TCC, fault indicator and DLC port. Red/blue PCM connector and EV1 fuel injector connector..
The 1200-degree glass fiber braid and connector position lock on all circuits are heated before leaving the factory to improve the performance and efficiency of the engine..
The length of the 60-AMP relay harness has been increased by 36 inches, which is convenient for computer installation and easy installation, and there is a complete installation manual..

This kit allows you to assemble up to four of these solid state relays on a single PCB and control them all via I2C from your favorite microcontroller..
The Quad Solid State Relay Kit comes with four solid state relays rated up to 40A at voltages between 28-380 VAC so you can switch some serious power with this board all from a single Qwiic connector attached to a low-powered microcontroller..
Features: Operating Voltage: 2.5-3.6V (3.3V recommended). I2C Address: 0x08 (Default), 0x09 (Alternate via jumper). Max Current (Through Relay): 40A (24-380VAC). Zero Cross Trigger. Normally Open Circuit Only.
Includes: 1x Qwiic Quad Solid State PCB. 4x Solid State Relay - 40A (3-32V DC Input). 8x 4-40 Hex Nut. 8x 3/8in. Phillips Machine Screw - 4-40 Thread. Hook-up Wire 8" - 22 AWG (Red). Hook-up Wire 8" - 22 AWG (Black).
Assembly required. Tools are not included. You will need a screwdriver and wire clippers/strippers..

Includes: 2 Lamps, 2 black stone shields/covers, 1 relay, 1 3-pin harness with DT connector, 1 fuse, 1 switch, mounting instructions.
LED driving lamp including LED accent light - in appealing rectangular shape.
The 450 LED driving lamp is designed for small installation spaces.
15 high-power LEDs and the full-surface faceted reflector ensure homogeneous illumination.