ReviewsResistance Strain Gage

Accusize Industrial Tools 81 Pcs Steel Gauge Block Set, Grade B, P900-S581

81 pc Grade B Steel Gage Block Set with MFG'S certificate.
Manufactured under carefully controlled conditions allowing for the highest degrees of accuracy when used at a temperature of 68 degrees F. (20 C)..
All gage block sets are assigned serial numbers and accompanied with a certificate of inspection listing the deviation for each block.
Each gage block set meets or exceeds federal specification ASME B89.1.9-2002..
Hardened to HRC 64 / All gage block sets are made to special standard to resist corrosion and defacement.

7.62 NATO CHAMBER HEADSPACE GAGE: The proper use of Headspace Gages is the most reliable way to test rifle chamber length. These rimless chambers require a slightly longer maximum headspace than commercial 308 Win calibers. The 7.62 NATO Headspace Gages do not conform to SAAMI tolerances..
MAXIMUM LENGTH: The Forster NATO Maximum rifle chamber gage checks to see that the rifle does not have excessive headspace, which could lead to dangerous pressure problems. The NATO Maximum Headspace Gage measures 1.6455″.
PRECISION MACHINED: Manufactured from top-quality, hardened steel and precision ground to ANSI and SAAMI tolerances. Headspace tolerance ground to a very exacting ±.00015..
QUALITY ASSURED: Each Headspace Gage thoroughly inspected with NIST-certified measurement tools to ensure the highest quality product..
MEASURING MEANINGFUL HEADSPACE: Properly speaking, and for safety purposes, one measures “headspace” as the difference between the length of a standard cartridge, as represented by a gage, and the gun’s actual chamber length , when the head of the cartridge is flush against the bolt face..

Fine thread Drywall--Sharp point: For attaching drywall to metal studs from 25 gage through 20 gage thick. Longer sizes are ideal for multiple layers or insulation. Fine thread Drywall--Drill point: Will drive easily through drywall, drill a hole in a steel stud up to 14 gage thick, and form its own mating thread. Can also be used for attaching plywood or insulation board to 14 gage metal.
Screws shall be quenched in liquid and then tempered by reheating to 650°F minimum.

Dillon Case Gage 45 ACP, Case Gage, reloading equipment, reloading parts, reloading accessories, 45 ACP case gage.

Gage increments are in .001" steps Minus tolerance: +0/-.0002". Fully hardened to 60-62 RC. Each gage is inspected and has a 10 Micron finish or better. Complete with plastic, element-proof fitted case..

Accurate Measurements: Used for accurately setting any bore gage up to 6" in diameter to an accuracy of 0.0001".
comes with a base anvil of 2.750" x 0.80" and 2 adjustable anvils of 2.375" x 0.375".
Bore Gage Capacity: This bore gage master has an internal capacity of 6.

Gage increments are in .001" steps Minus tolerance: +0/-.0002". Fully hardened to 60-62 RC. Each gage is inspected and has a 10 Micron finish or better. Complete with plastic, element-proof fitted case..

9 different health information at a glance, User-friendly Graph, BIA Technology / ITO Conductive surface.
Compatibility iOS 5.0, Android 4.3, Bluetooth 4.0 or higher, Unlimited user members.
Wide enough scale to adult male too!, Super-Clear Large LED Display, Automatic On & Off feature by stepping-on & down.
Stability & Durability up to 396lb/180kg, High Precision Strain Gage for accurate weighing, Special gift for your lover, family, and....

350 LEGEND: Use to check headspace of 350 Legend..
RIMLESS CARTRIDGE HEADSPACE: The proper use of Headspace Gages is the most reliable way to test rifle chamber length. Headspace in a rimless cartridge is the distance between the bolt face and a datum line, determined by SAAMI, where the front of the cartridge rests on its shoulder when the bolt is closed..
NO-GO: Corresponds to the maximum headspace we recommend for gunsmiths’ chambering new bolt-action rifles. This is not a SAAMI-maximum measurement. If a rifle closes on a NO-GO gage, it may still be within SAAMI specifications, or it may have excessive headspace. To determine if there is excessive headspace, the chamber should then be checked with a FIELD gage. The NO-GO gage is a valuable tool for gunsmiths’ reaming new chambers, in order to ensure tight and accurate headspace.
PRECISION MACHINED: Manufactured from top-quality, hardened steel and precision ground to ANSI and SAAMI tolerances. Headspace tolerance ground to a very exacting ±.00015. Each Headspace Gage thoroughly inspected with NIST-certified measurement tools to ensure the highest quality product..
MEASURING MEANINGFUL HEADSPACE: Properly speaking, and for safety purposes, one measures “headspace” as the difference betwee....

NO-GO: Corresponds to the maximum headspace we recommend for gunsmiths’ chambering new bolt-action rifles. This is not a SAAMI-maximum measurement. If a rifle closes on a NO-GO gage, it may still be within SAAMI specifications, or it may have excessive headspace. To determine if there is excessive headspace, the chamber should then be checked with a FIELD gage. The NO-GO gage is a valuable tool for gunsmiths’ reaming new chambers, in order to ensure tight and accurate headspace..