ReviewsReturn Path Amplifier

Arris 1-Port Cable, Modem, TV, OTA, HDTV Amplifier Signal Booster with Passive Return and Coax Cable Kit

  • The BDA-42-1-PR-R is a Bi-Directional Cable TV Amplifier and over-the-air (OTA) HDTV amplifier designed for use in homes. Boosts signal by 32x in the forward path.
  • Compatible with all standard and digital Cable TV services. The amplifier should be installed BEFORE splitters and long cable runs for best results. 1-year warranty..
  • Meets all applicable IEEE surge standards for all output ports, which enhances system reliability. Weather seal and protective coating allow use of the amplifier for indoor or outdoor applications. 36" connection cable included..
  • NOT FOR USE WITH SATELLITE DISH SYSTEMS. It will block the signal between the dish and receiver. NOT FOR USE WITH AMPLIFIED ANTENNAS. Using with an amplified antenna may cause total loss of OTA signals. If you antenna comes with any type of power cord, it is amplified..
Check Stock

Blue 1967 Yeti Pro USB Condenser Microphone Multipattern

  • Three custom condenser capsules and four different polar pattern settings: Cardioid, Stereo, Bidirectional and Omnidirectional.
  • Cutting-edge A-D converter chip and separate analog circuit path for use with professional studio mixers and preamps.
  • Built-in headphone amplifier for zero-latency monitoring, and direct controls for headphone volume, pattern selection, mute, and microphone gain.
  • 15 Hz - 22 kHz frequency response. Headphone Amplifier: Signal to Noise 114dB. Yeti Pro is not capable of simultaneous analog and digital operation.....
  • 192 kHz/24 bit Sample/Word. Proprietary capsule design to capture sounds with detail and articulation.
Check Stock

Kicker CVR104 10 Bundle with Crunch PX2000.1D 2000 Watt Max Mono Amp Wire Kit

  • Maximum low voltage signal from the source unit comes into the amplifier through a low voltage circuit which delivers minimal distortion through the....
  • Highest sound quality connection with quality RCA materials helps prevent interference and minimize distortion in the signal path.
  • Easily tie into OEM audio systems that do not offer RCA output to maximize after market amplifier power.
Check Stock

Blue 1967 Yeti Pro USB Condenser Microphone Multipattern Renewed

  • Three custom condenser capsules and four different polar pattern settings: Cardioid, Stereo, Bidirectional and Omnidirectional.
  • Cutting-edge A-D converter chip and separate analog circuit path for use with professional studio mixers and preamps.
  • Built-in headphone amplifier for zero-latency monitoring, and direct controls for headphone volume, pattern selection, mute, and microphone gain.
  • 15 Hz - 22 kHz frequency response. Headphone Amplifier : Signal to Noise 114dB. Yeti Pro is not capable of simultaneous analog and digital operation.....
  • 192 kHz/24 bit Sample/Word. Proprietary capsule design to capture sounds with detail and articulation.
Check Stock

Arris 4-Port Bi-Directional Cable TV, OTA, Satellite HDTV Amplifier Splitter Signal Booster with Passive Return And Coax Cable Package - cableTVamps®

  • The BDA-42-4-PR-R is a Bi-Directional Cable TV Amplifier and over-the-air (OTA) HDTV amplifier designed for use in homes. Boosts signal by 5x in the forward path..
  • Compatible with all standard and digital Cable TV services. The amplifier should be installed BEFORE splitters and long cable runs for best results. 1-year warranty..
  • Meets all applicable IEEE surge standards for all output ports, which enhances system reliability. Weather seal and protective coating allow use of the amplifier for indoor or outdoor applications. 36″ White connection cable and PCT-TT installation tool included..
  • NOT FOR USE WITH SATELLITE DISH SYSTEMS. It will block the signal between the dish and receiver. NOT FOR USE WITH AMPLIFIED ANTENNAS. Using with an amplified antenna may cause total loss of OTA signals. If you antenna comes with any type of power cord, it is amplified..
Check Stock

Autotek Mean Machine 4000W Mono Amplifier 1-Ohm Stable Car Audio Amp (4 Pack)

  • Minimize Distortion – Highest sound quality connection with quality RCA materials helps prevent interference and distortion in the signal path. Easily tie into OEM audio system that do not offer RCA output to maximize after-market amp power..
  • Built for Powerful Sound – Maximize power efficiency while improving sound quality and minimizing distortion with the high speed Pro-Fi MOSFET components. A high energy power supply delivers power with minimal impact on the electrical system..
  • Class A/B Amplifier – Class A/B topology and low noise preamplifier circuitry produces high quality sound and allows the amplifier to develop high levels of power with minimal distortion..
  • Aluminum Heat Sink – Quick Thermal Dispersion (QTD) technology assures additional mass in the aluminum heat sink keeping the amplifier running cool, with nearly undetectable distortions during normal use when listening to music..
  • High Quality Connections – Nickel plated brass connection with terminals allows secure connections while resisting corrosion. Screw down connectors allow for easy access with hand tool for quick and secure connection..
Check Stock

REGA Fono Moving Coil MK4 Phono Stage

  • The Rega Fono MC is an exceptionally high quality MC phono stage designed to maximise the potential of any MC cartridge..
  • The Rega Fono MC has been designed to be effective, easy to use, and above all, to reproduce music. The Fono MC uses the Linear Systems low noise LSK389 FET in an all discrete input stage where low noise and linearity are vitally important to get the best from an MC cartridge.
  • A MUSE operational amplifier is used in the RIAA equalization amplifier. Polypropylene capacitors have been used in the signal path and in the RIAA equalization circuits..
  • The aesthetic design of the Fono MC was as important as the quality of its electrical capabilities, so it benefits from the same aluminium case as the Rega TTPSU and Fono MM amplifier, giving it a design which offers a familiar feel and moreover brings it in line with its illustrious bigger brothers.
  • Frequency response (50KΩ output load) = 13Hz (-3dB) to 100KHz (-0.3dB) RIAA accuracy (50KΩ output load) = Better than +/-0.2dB 100Hz to 100KHz Power requirements = 24V AC at 150mA maximum. Only to be used with Rega PS1..
Check Stock

REGA Fono MM Phono Stage

  • The new Rega Fono MM phono stage has been designed to be effective, easy to use, and above all, to reproduce music..
  • The Fono MM uses a fully discrete, cascaded, complementary amplifier input stage, a configuration designed to optimise the performance of your moving magnet cartridge..
  • The RIAA equalization has been split into two stages to minimise interaction. Polyester capacitors have been used in the signal path and polypropylene capacitors are used in the RIAA equalization circuits..
  • The aesthetic design of the Fono MM was as important as the quality of its electrical capabilities, so it benefits from the same aluminium case as the Rega TTPSU and Fono MC amplifier, giving it a design which offers a familiar feel and moreover brings it in line with its illustrious bigger brothers..
  • Input sensitivity = 1.7mV for 200mV output, Input loading = 47KΩ in parallel with 100pF, Maximum input level = 60mV at 1KHz, Recommended minimum output load resistance = 5KΩ.
Check Stock

Crunch PX2000.1D 2000W X Series Class D Monoblock Subwoofer Amplifier - PRE-AMP Circuitry Low Noise PreAmplifier Crossover/Signal Shaping w/ 4 Gauge Amp Kit

  • Maximum low voltage signal from the source unit comes into the amplifier through a low voltage circuit which delivers minimal distortion through the....
  • Highest sound quality connection with quality RCA materials helps prevent interference and minimize distortion in the signal path.
  • Easily tie into OEM audio systems that do not offer RCA output to maximize after market amplifier power.
Check Stock

Autotek TA1250.2 TA Series 2 Channel Car Audio Amplifier (Black) – Class A/B Amp, 1200 Watt, Bass Boost, Marine Grade Protection Amplifier

  • Minimize Distortion – Highest sound quality connection with quality RCA materials helps prevent interference and distortion in the signal path. Easily tie into OEM audio system that do not offer RCA output to maximize after-market amp power..
  • Built for Powerful Sound – Maximize power efficiency while improving sound quality and minimizing distortion with the high speed Pro-Fi MOSFET components. A high energy power supply delivers power with minimal impact on the electrical system..
  • Class A/B Amplifier – Class A/B topology and low noise preamplifier circuitry produces high quality sound and allows the amplifier to develop high levels of power with minimal distortion..
  • Aluminum Heat Sink – Quick Thermal Dispersion (QTD) technology assures additional mass in the aluminum heat sink keeping the amplifier running cool, with nearly undetectable distortions during normal use when listening to music..
  • High Quality Connections – Nickel plated brass connection with terminals allows secure connections while resisting corrosion. Screw down connectors allow for easy access with hand tool for quick and secure connection..
Check Stock

Rega Aria V2 Flagship MM/MC FET Phono Preamplifier

  • ...a fresh new look and match the range are two entirely separate, high performance phono stages. One fully adjustable, dedicated moving coil and one moving magnet. Each stage is designed and engineered to maximise the potential of your vinyl system whilst remaining easy to use and set up..
  • The Aria is an "all analogue amplifier" with no digital control circuitry. The fully aluminium case screens the internal circuit from any stray RFI signals. Our designers have avoided including any superfluous gadgets as they obstruct the signal path and degrade the sound quality. The Aria incorporates many innovative design ideas including a self-adjusting servo control to keep the MC input circuit at its optimum, compensating for any variations in ambient or operating temperature..
  • Both stages have their own separate input sockets and input pre-amplifier circuitry. This enabled us to design bespoke input circuitry for each cartridge type without compromise. Signal switching is performed at high level and low impedance (via relays) ensuring there is no degradation of the signal..
  • The MC input uses parallel connected, low noise FET's (Field Effect Transistor's) configured as a compound pair. The use of FET transistors ensures there is no bias current flowing in the cart....
Check Stock