ReviewsRigid Design

uxcell 1/8 inch to 5mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

Connection Diameter: 1/8 inch to 5mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

uxcell 5mm to 5mm Bore Rigid Coupling Set Screw L25XD14 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Blue

Connection Diameter: 5mm to 5mm, Total Length: 25mm /0.98 inch, Outside Diameter : 14mm/ 0.55 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

Blind into the Breach (The Hunter Imperium Book 4)

...igid truss is formed allowing the CAGE Permanent Hub Blind to support and excess of 800 lbs allowing your blind to hold up to strong winds and the heaviest of snow loads..
WITHSTAND ALL-WEATHER BONDED FABRIC - Our premium all-weather fabric is a bonded three-layer material design to withstand a constant barrage of wind and rain without failure. The exterior is made with heavy-duty solution dyed polyester while the interior fabric is black which maximizes concealment. In between the two fabrics is a waterproof/windproof membrane that will continue to keep out the elements even after years of rough use..
5-MINUTE SET UP - The CAGE Permanent Hub Blind functions much like a typical hub blind and sets up in a matter of minutes but can be left out for years of use like other permanent sets..
ROOMY INTERIOR - The interior of the blind is over 7’ wide and 7’ long between the walls and features plenty of headroom measuring 76” tall at the center..
WATERPROOF DESIGN - The entire blind is designed to stay bone dry inside. There is a seam sealed rain fly over the entire structure and add....

Check Stock

uxcell 6mm to 10mm Bore Rigid Coupling Set Screw L22XD16 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

Connection Diameter: 6mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L22XD16 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

Connection Diameter: 10mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

uxcell 6mm to 6mm Bore Rigid Coupling Set Screw L22XD14 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

Connection Diameter: 6mm to 6mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

uxcell 5mm to 8mm Bore Rigid Coupling Set Screw L22XD14 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

Connection Diameter: 5mm to 8mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

uxcell 8mm to 8mm Bore Rigid Coupling Set Screw L22XD14 Stainless Steel,Shaft Coupler Connector,Motor Accessories,2pcs

Connection Diameter: 8mm to 8mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

Ski-Doo New OEM, Branded REV Gen4 LinQ 21 Liter Tunnel Bag, 860201740 860202449

17-liter (4.5 US gallons, 1037 cu in) capacity..
Fits REV-XM, REV-XS, REV-XP, REV-XR (except GTX, Grand Touring), does not fit on REV-XU Tundra.

Check Stock

uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L25XD16 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Blue,2pcs

Connection Diameter: 10mm to 10mm, Total Length: 25mm /0.98 inch, Outside Diameter : 16mm/ 0.63inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock

uxcell 8mm to 10mm Bore Rigid Coupling Set Screw L25XD16 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Blue,2pcs

Connection Diameter: 8mm to 10mm, Total Length: 25mm /0.98 inch, Outside Diameter : 16mm/ 0.63 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..

Check Stock