ReviewsSata Breakout Board

Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino

  • Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
  • Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
  • The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
  • There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
  • Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
Check Stock

3 Axis Stepper Motor CNC Router Kit Nema23 425oz-in 112mm Dual Shaft+CW5045 Driver 4.5A 256 microstep+400W 36V Power Supply CNC Controller Kit for Engraving Lathe Plasma Milling Drilling Machine

  • ♞【Product】3 Axis nema23 stepper motor driver controller kit.
  • ♞【Application】This cnc kit are widely used in engraving machine, printer,....
  • ♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
  • ♞【Driver】CW5045 driver Voltage: DC 24-50V.
  • Current: rated maximum output reaches: ±4.5A.
  • ♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
  • ♞【Power supply】400W,36V/9.7A switching power supply.
Check Stock

C25S - Smooth Stepper Terminal Board

  • Full access to all the pins of the Smooth Stepper Board. Connects directly to the Smooth Stepper (from Warp9). The board is provided with sockets that allow the Smooth Stepper Board to be plugged directly into this board. No ribbon cables required. When using the Smooth Stepper board there is no need to use an additional power supply to power the board. It will draw power from the Smooth Stepper board. Built-in Passive Low Pass Filters for the all inputs..
  • C25 Smooth Stepper Breakout Board with push lock terminals.
Check Stock

Treedix RPi GPIO Terminal Block Breakout Board Module Expansion Board Compatible with Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W

  • Easy to operate: Use this module to easily extend the Raspberry pi Zero project to the Internet of Things or industrial control applications.
  • There is a mark on the breakout board that can clearly identify the pin position, Breakout board is of excellent quality and adopts double-sided gold forming process.
  • The module is small in size and does not occupy other space. It is very convenient when making DIY circuits, and the wires can be easily inserted into the terminals.
  • Compatible with Raspberry Pi: This GPIO terminal block is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W.
  • Note: This project needs to be welded and assembled by yourself.
Check Stock

Geekworm X820 V3.0 2.5“ SATA HDD/SSD Storage Expansion Board, USB 3.0 Mobile Hard Disk Module for Raspberry Pi 3 B+/3B/ROCK64/Tinker Board&2.5 Inch SATA HDD/SSD

  • ✔ Please use this high quality certified DC 5V 4A power supply(ASIN :B07413Q5Y4).Power supply request: 5Vdc +/-5% , 4A.
  • The power adapter not only powers Raspberry Pi board but also powers your SSD or HDD. If the power is low, the SSD/HDD may not be identified or damage your RPi or X820 board. [Do Not Use ASIN:B01K0608A0!!!].
  • ✔ Raspberry Pi SATA X820 V3.0 HDD/SSD USB3.0 shield expansion board provides an complete storage solution for Raspberry Pi motherboard/ROCK64, Support up to 4TB 2.5 inch SATA interface hard disk drives (HDD) / solid-state drive (SSD). A good raspberry pi sata adapter for Raspberry Pi 3B+, 3B, 2B, B+, ROCK64. Note: For Raspberry Pi 4 Model B 2.5 inch SATA HDD/SSD storage board, please refer to ASIN:B07VXF2HJG.
  • For Raspberry Pi 4 Model B mSATA SSD storage board, please refer to ASIN: B07VXFGFLX.
  • ✔ X820 V3.0 supports USB booting from your HDD/SSD('reboot' command is supported), a useful and reliable function to every raspberry pi users or fans. Suggest to use with geekworm x820 metal case(ASIN :B07GRZRW7J).
  • User manual, pls refer to Geekworm WiKi search(X820)..
  • ✔ Powers the Raspberry Pi via Pi's 40-pin header or Micro USB socket.
  • Furthermore, On-board XH2.54 connector and USB power socket (5V 2A output) to power other devices,....
Check Stock

GeeekPi Raspberry Pi Mini Tower NAS Kit, Raspberry Pi ICE Tower Cooler with PWM RGB Fan, M.2 SATA SSD Expansion Board, GPIO 1 to 2 Expansion Board for Raspberry Pi 4 Model B

  • This Raspberry Pi Mini Tower NAS kit contains an M.2 SATA SSD expansion board which can expand the mass storage for your Raspberry Pi. The case is made of ABS material,This kit turns your Raspberry Pi into a mobile mini-host..
  • NOTE: The RGB light on Fan and mood light will not light up unless installed driver, and OLED will not display any information untill you have enabled it !!! Please read the manual carefully and follow the steps to enable it.Please purchase M.2 SATA SSD 2280 mass storage device, It dose NOT support NVME SSD!!!.
  • M.2 SATA SSD 2280/2260/2240 mass storage adapter board,supports up to 2TB M2. SATA SSD solid-state drive.
  • Package Includes: 1 x ABS Mini Tower Case,1 x ICE-Tower CPU Cooling Fan,2 x Acrylic Side Panel,1 x 0.96inch OLED Display (Already mounted on the case ),1 x GPIO Edge expansion board,1 x M.2 SATA SSD Shield,1 x Assembly manual(Note: Raspberry Pi 4B is Not included in the package).
Check Stock

Atomos Shogun Inferno | 7 Inch Touchscreen Recording Camera Monitor Bundle with SanDisk 240GB Ultra II Internal Solid State Drive + Pearstone 7.5" Articulating Arm

  • 7″ SuperAtom 325 PPI 1920×1200 IPS Touch Screen.
  • With compatible SanDisk 250GB 3D SATA III 2.5″ Internal SSD.
Check Stock

Adaptec RAID 71605 Storage Controller 2274400-R

  • ▶【8 Ports SATA 3.0 Adapter Card】: Acasis SATA card is equipped with 8 SATA 3.0 interfaces and supports the simultaneous connection of 8 SATA hard disks, the transfer speeds up to 6Gbps, You could add 8 6Gb/s SATA 3.0 devices to your computer with this PCIe SATA card.
  • ▶【Easy to Install】: PCIe to SATA 3.0 Host Controller Card with a standard profile Bracket, PCIE Gen 2 X1 interface design, will works on PCIE X1, X4, X8, X16 slot, compatible with most size chassis on the market. Users need to check if PCs or Servers have at least one PCIE X1 slot on mother board before purchase.
  • ▶【80TB Expansion】: 8 Ports SATA 3.0 interfaces can expand to 80 TB, provide a high-volume database for your workstation and computer equipment. With using The chip JMB575+JMB1064 Chipset, improve this card more stable and compatible.
  • ▶【Supports Soft-RAID Mode】: The system comes with soft RAID and support four storage modes: RAID1 (SAFE Mode), AHCI1 (PM Mode), SPAN (BIG Mode) and RAIDO (FAST Mode). Supports Windows 7/ 8.1 / 10 / Linux, install the driver before add the HDD in system.
  • ▶【What You Get】 : 1 x 8-port SATA 3.0 controller card, 8 x SATA cable, 2 x SATA power splitter cable, 1 x user manual.
Check Stock

GeeekPi Raspberry Pi 4 SATA Storage, Raspberry Pi 4 Model B 2.5 inch SATA HDD/SSD Expansion Board X825 V2.0 USB3.0 Shield (Only for Raspberry Pi 4B)

  • Only For Raspberry Pi 4 Model B, supports up to 4TB 2.5 inch SATA hard disk drives (HDD) / solid-state drive (SSD), Only 2.5 inch SATA interface HDD/SDD hard disk is suitable for X825 board.
  • X825 Case,please refer to ASIN: B093WYWVRX.
  • Power supply request: AC 100 - 240V input 50 / 60Hz, 5V DC 4A output , Please use high quality DC 5V 4A power supply, highly recommend to use ASIN: B07YJDS71K(With TUV,FCC,RoHS,CE Certifications). If you get low quality power supply to use, it may probably will damage your 2.5 inch HDD/SSD or not recognize the HDD/SSD ..
  • OS compatiable: All Raspberry Pi operating systems.
  • USB 3.1 Gen1 to SATA 6Gb/s Bridge Controller.
  • Package Includes:1 x X825 V2.0 Expansion Board, 1 x USB 3.1 connector ,1 x Mounting Screws Pack.
  • Note: The Raspberry Pi 4B board and the 2.5" SATA HDD/SSD are Not Included.
Check Stock

Atomic Pi Developers Kit

  • Powerful Atom quad-core processor with 2Gb ram and 16GB Flash on board.
  • Developer kit includes large breakout board and AI camera module.
  • Gigabit Ethernet, AC WiFi, Bluetooth, Hi Performance Audio, USB-2, USB-3, SD, GPIO.
  • Peripherals include 9-axis sensor, bluetooth and XMOS audio power-amp.
  • Boots Linux right out of the box. What will you make with it?.
Check Stock

GeeekPi Raspberry Pi Mini Tower NAS Kit, Raspberry Pi ICE Tower Cooler with PWM RGB Fan, M.2 SATA SSD Expansion Board, GPIO 1 to 2 Expansion Board, 18W QC3.0 Power Supply for Raspberry Pi 4 Model B

  • This Raspberry Pi Mini Tower NAS kit contains an M.2 SATA SSD expansion board which can expand the mass storage for your Raspberry Pi. The case is made of ABS material,This kit turns your Raspberry Pi into a mobile mini-host..
  • NOTE: The RGB light on Fan and mood light will not light up unless installed driver, and OLED will not display any information untill you have enabled it !!! Please read the manual carefully and follow the steps to enable it.Please purchase M.2 SATA SSD 2280 mass storage device, It dose NOT support NVME SSD!!!.
  • The 0.96 inch OLED screen was already mounted on the case.28x64pixels, default I2C address: 0x3C.
  • M.2 SATA SSD 2280/2260/2240 mass storage adapter board,supports up to 2TB M2. SATA SSD solid-state drive.
  • Package Includes: 1 x ABS Mini Tower Case,1 x ICE-Tower CPU Cooling Fan,2 x Acrylic Side Panel,1 x 0.96inch OLED Display (Already mounted on the case ),1 x GPIO Edge expansion board,1 x M.2 SATA SSD Shield,1 x QC 3.0 Power supply,1 x Assembly manual(Note: Raspberry Pi 4B is Not included in the package).
Check Stock