ReviewsServo To Breakout Board

Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino

Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.

Check Stock

10 pcs 3.93inch JR Style Servo Extension Cable Lead Wire - 3-Pin JR Plug Male to Male RC Servo Wire Extension Cord

3-Pin JR plug male to male connector servo extension lead wire cable..
There is a 3 pin JST RE connector on each end. This is a simple 3 wire cable. Ideal for jumping from board to board, or something else..
Practical range: For Airplane, Helicopter, Quad co-pterter , Multi-coater RC car servo connection or receiver connection..
Packaging quantity ：10 Pcs * 10cm JR 3pin male to male plug servo extension cables wires cords leads..

Check Stock

15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.

Check Stock

3 Axis Stepper Motor CNC Router Kit Nema23 425oz-in 112mm Dual Shaft+CW5045 Driver 4.5A 256 microstep+400W 36V Power Supply CNC Controller Kit for Engraving Lathe Plasma Milling Drilling Machine

♞【Product】3 Axis nema23 stepper motor driver controller kit.
♞【Application】This cnc kit are widely used in engraving machine, printer,....
♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
♞【Driver】CW5045 driver Voltage: DC 24-50V.
Current: rated maximum output reaches: ±4.5A.
♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
♞【Power supply】400W,36V/9.7A switching power supply.

Check Stock

MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano

Note: The Raspberry Pi and Servo in the photo are not included. User Manual: Please get the link from the operation guide below.
Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven.
2.You should connect higher power supply for higher-power servo.
3.Make sure servo are connected properly, otherwise they will not move..
Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you..
Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano..
Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..

Check Stock

5pcs LED Breakout Module Board WS2812 RGB 5050 RGB with WS2812S chip Used for 5050 RGB LED

【Introduction】- The breakout board uses WS2812S chip, used for 5050 LED..
【Support】- This WS2812 Breakout Board supports high brightness and RGB color..
【Can Connect a Lot of Lights】- Built in chip, it can connect a lot of lights in series..
【Operation】- After connection in series, each light can control color independently..
【Power Supply】- No matter for how much lights, it only need one control cable and two power cables..

Check Stock

C25S - Smooth Stepper Terminal Board

Full access to all the pins of the Smooth Stepper Board. Connects directly to the Smooth Stepper (from Warp9). The board is provided with sockets that allow the Smooth Stepper Board to be plugged directly into this board. No ribbon cables required. When using the Smooth Stepper board there is no need to use an additional power supply to power the board. It will draw power from the Smooth Stepper board. Built-in Passive Low Pass Filters for the all inputs..
C25 Smooth Stepper Breakout Board with push lock terminals.

Check Stock

Treedix RPi GPIO Terminal Block Breakout Board Module Expansion Board Compatible with Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W

Easy to operate: Use this module to easily extend the Raspberry pi Zero project to the Internet of Things or industrial control applications.
There is a mark on the breakout board that can clearly identify the pin position, Breakout board is of excellent quality and adopts double-sided gold forming process.
The module is small in size and does not occupy other space. It is very convenient when making DIY circuits, and the wires can be easily inserted into the terminals.
Compatible with Raspberry Pi: This GPIO terminal block is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W.
Note: This project needs to be welded and assembled by yourself.

Check Stock

DIYmall 10pcs 10cm 3.93inch Male to Male JR Plug Servo Extension Lead Wire Cable 3Pin 100mm for RC Plane

10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
Great for jumping from board to board or just about anything else..
There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
Length:100mm Type:JR Plug Servo Extension wire (Male to Male).

Check Stock

6Pcs ShareGoo JR Style Servo Splitter Cable, 2.75' Servo 1 Male to 2 Female JR Y Harness Y Cable Extension Wire for RC Models Car Airplane Helicopter Drone Boat

Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
This servo Y-cable allows you to control two servos with one radio channel..
Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..

Check Stock

4 Axis Stepper Motor Nema 23 Dual Shaft 425oz-in 112mm+CW5045 Driver 4.5A 256 Microstep+5 Axis Breakut Board+400W 36V Power Supply CNC Controller Kit for CNC Router Engraver Milling Machine

♞【Stepper Motor】4pcs 23HS2430B nema23 stepper motor.
♞【Stepper Motor Driver】4pcs CW5045 driver, current: 1.3A-4.5A.
Driver microstep: 1 (1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5,....
♞【Control Board】1pcs 5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
♞【Power supply】1pcs 400W,36V/9.7A switching power supply.
♞【Application】This cnc kit are widely used in engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile....

Check Stock