ReviewsServo To Multiplexer Board

DEVMO 2PCS CD74HC4067 16 Channel Analog Digital Multiplexer MUX Breakout Board CD74HC4067 Precise Module Compatible with Ar-duino DIY

• ★This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
• ★6ns break-before-make @ 4.5V,"On" resistance: 70 Ohms @ 4.5V.
• ★Wide operating temperature range: -55C to 125C.
• ★Package Includes: 1PCS 16 Ch. Mulitplexer,2PCS Header Pins as shown above.

20Pcs HEF4051BT SOP-16 HEF4051B SOP16 F4051B 8-Channel Analog multiplexer/demultiplexer

Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino

• This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx)..
• It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction..
• To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
• Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
• The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prev....

KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino

• This expansion board can directly stack on the controller R3 board and can drive up to 16 servos.
• Uses I2C input, just occupy A4 and A5 interface on the control board.
• Contains PCB double sided holes, can direct to solder with components to build up prototyping circuits.
• Servo power supply independent V + input up to 6V.
• How to use: Search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product..

Arduino Uno 3 Ultimate Starter Kit Includes 12 Circuit Learning Guide

• This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
• Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
• Includes a total of over 190 electronic parts and components.

sb components Motor Driver Board for The BBC Micro bit 2 Channel DC Motors and 3 Channel Servos Motors Motor Driver for Micro bit BBC microbit Motor Driver Board

• micro:bit edge connector, directly pluggable.
• 2x DC motor interfaces, 3x servo interfaces.
• Integrates 5V regulator, up to 3A output current.
• Onboard multi connector options for DC motors in different specifications, onboard standard servo headers.

Kiro&Seeu 2PCS CD74HC4067 16 Channel Analog Digital Multiplexer MUX Breakout Board CD74HC4067 Precise Module Compatible with Ar-duino DIY D74HC4067-16CH-2P

• Use the CD74HC4067 16-channel analog signal switch.
• Analog signal input: C0-C15 16 channels..
• This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067..
• This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction..
• To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

• MKS servo42C is a product developed by MKS to meet market demand. The closed-loop motor uses the motor's rotation angle feedback to the drive circuit to detect whether every step that should be taken has been taken to prevent losing steps. If a closed loop occurs, the motor will make up or lose steps through the feedback information, and the blue LED on the closed loop module will light up..
• Support 1-256 subdivision,odd subdivision (such as 11 subdivision) is also available. And support motors with 0.9 degree or 1.8 degree. Maximum speed 1000RPM. With usart interface, you can connect the computer by serial port, for parameter adjustment and query..
• Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
• Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
• Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User metho....

12Pcs CD74HC4067 16-Channel Analog Digital Multiplexer MUX Breakout Board Module CD74HC4067 CMOS Precise Module Compatible with DIY

• CD74HC4067 board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer, use the CD74HC4067 16-channel analog signal switch.
• It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
• The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”)..
• To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins..
• Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devi....

Barnabas Robotics Servo Motor Tester Kit | 180 Degree 9g Servo Motor + RC Servo Tester Controller + 6V Battery Holder

• [CONVENIENT, ALL-IN-ONE KIT FOR TESTING SERVO MOTORS] Experiment with servo motors with this all-inclusive kit. Includes 9g servo motor + servo tester controller + 6V battery holder at a low price!.
• [9G Servo Motor] 180 degree range of motion. Includes 3 types of servo horns..
• [4 CELL x AA BATTERY HOLDER] Fits 4 x AA batteries, which produces 6V for your servo tester and servo motors..
• [SERVO TESTER] Includes 3 modes to test servo motors or ESC.
• [GREAT FOR RC APPLICATIONS] Use as a power source for robotics, RC cars, helicopters, planes, boats and or any hobby projects.

100PCS CD4053 CD4053B CD4053BE DIP-16 Analog Multiplexer IC

• It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
• The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
• Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
• This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
• Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..