ReviewsSingle Sheave Pulley

Koch 3250393 3 Snatch Block Double Sheave

• Made of 304 stainless steel, sturdy, anti-rust and corrosion-resisttant with strong structure.
• Rope Size Range: 3/8-1/2 Inches, Sheave Diameter: 2 Inches, Overall Length: 5 Inches.
• Easy installation of a flexiable sliding pulley for kayaks, canoes, construction, household project.
• Smooth turning wheels, 360 degree rotation to prevent rope or cable from knotting.

Petzl P03A Mobile Versatile Ultra-Compact Pulley

• Designed for hauling systems and deviations.
• Sheave mounted on self-lubricating bushings for good efficiency.

CAMP Andry Mobile Pulley

scottchen PRO 3' Heavy Duty Garage Door Pulley Kits, 3/8' Arbor 200LB Load, 4 Sheave Pulleys, 2 Clevis Forks, 4 Bolts and Nuts Kit

• 【Function】This 3in garage door pulley kit designed to repair or replace damaged parts of your old, worn, noisy and jumping doors. Provide a quiet, smooth and pleasant door opening/closing..
• 【Compatible】The 3in sheave pulley is 3/8” bore and 3/8” cable groove, which adapt to most commonly garage doors and accept max 5/16” diameter pulling cable or straps..
• 【Valued Package】The package include 4 pulleys and 2 clevis forks, this can be used as 2 fixed pulleys plus 2 sliding clevis wheel pulleys, fulfill your various demand. Coming with 4 screws and nuts, saving your time to look for from drawer or corner..
• 【High Quality】The garage door pulley system is heavy duty, 200lb load rating for doors up to 400lb. Durable steel construction, center race with 9 ball bearings and pre-lubricated in factory for smooth sliding..
• 【Kindly Reminder】Professional installation is recommended. If DIY, please remember wearing safety guard always, using the proper tools and install properly..

Phoenix Mfg. V-Groove Drive Pulley, 2'' Diameter, 5/8\ Bore, Die Cast

• Pulley outside diameter is 1.85 inch, 1 Groove.
• Cast iron for resistance to wear and galling.
• Standard V-belt Sheave Use with A, 3L & 4L (A & AX) V-Belts.
• Inner diameter:3/4inch, Bore type:Fixed Bore.
• Enjoy a smooth&worry-free return service within a month.

Martin 3020 2 Taper Bushing, Sintered Steel, Inch, 2\ Bore, 4.25\ OD, 2\ Length

• Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
• Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
• Sintered steel for greater strength and resistance to wear than steel.
• Keyed to the shaft to prevent the shaft from rotating in the bushing.
• Interchangeable with taper bushings from various manufacturers.

Mytee Products Snatch Block with Hook WLL 2 Ton 3 Sheave 3/8 Inch Wire Rope Wrecker Roll Back Recovery

• The snatch block is a pulley system with covered and protected yet removable sides..
• Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..

Mytee Products Snatch Block with Hook WLL 8 Ton 6 Sheave 3/4 Inch Wire Rope Wrecker Roll Back Recovery

• The snatch block is a pulley system with covered and protected yet removable sides..
• Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..

Martin 2517 1 1/2 Taper Bushing, Sintered Steel, Inch, 1.5\ Bore, 3.375\ OD, 1.75\ Length

• Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
• Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
• Sintered steel for greater strength and resistance to wear than steel.
• Keyed to the shaft to prevent the shaft from rotating in the bushing.
• Interchangeable with taper bushings from various manufacturers.

Martin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length

• Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
• Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
• Sintered steel for greater strength and resistance to wear than steel.
• Keyed to the shaft to prevent the shaft from rotating in the bushing.
• Interchangeable with taper bushings from various manufacturers.

Martin 2517 2 7/16 Taper Bushing, Sintered Steel, Inch, 2.44\ Bore, 3.375\ OD, 1.75\ Length

• Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
• Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
• Sintered steel for greater strength and resistance to wear than steel.
• Keyed to the shaft to prevent the shaft from rotating in the bushing.
• Interchangeable with taper bushings from various manufacturers.