ReviewsSingle phase Motor Capacitors

LM YN AD8302 Wideband Logarithmic Amplifier Wideband Linear Multiplier Phase Detector Module Low Frequency to 2.7G for OPA695

  • ...ons. It requires few external components and a single supply of 2.7 V–5.5 V. The ac-coupled input signals can range from –60 dBm to 0 dBm in a 50 ohm system, from low frequencies up to 2.7 GHz. Both subsystems have an output bandwidth of 30 MHz, which may optionally be reduced by the addition of external filter capacitors. 003cbr003e.
  • The AD8302 can be used in controller mode to force the gain and phase of a signal chain toward predetermined setpoints.003cbr003e.
  • The AD8302 includes a phase detector of the multiplier type, but with precise phase balance driven by the fully limited signals appearing at the outputs of the two logarithmic amplifiers. Thus, the phase accuracy measurement is independent of signal level over a wide range. The signal inputs are single-ended, allowing them to be matched and connected directly to a directional coupler. Their input impedance is nominally 3 kΩ at low frequencies. 003cbr003e.
  • The phase and gain output voltages are simultaneously available at loadable ground referenced outputs over the standard output range of 0 V to 1.8 V. The output drivers can source or sink up to 8 mA. A loadable, stable reference voltage of 1.8 V is available for precise repositioning of the output range by the user.003cbr003e.
Check Stock

VFD 220V 0.75KW 1hp Variable Frequency Drive CNC VFD Motor Drive Inverter Converter for Spindle Motor Speed Control HUANYANG HY-Series(0.75KW, 220V)

  • IMPORTANT NOTE: this VFD is applicable to THREE phase motor and NOT support external resistor.Fan runs all the time even though the motor isn't (fan functions need to be customized)..
  • This drive is very suitable for HIGH-SPEED ROTATION motors,such as spindle motor, engraving machine CNC.Work with 220V single phase input and 220V three phase input.you can just connected L1/L2 to any two of VFD input R/S/T.
  • This VFD can be used for constant torque loads (such as hard starting: Air compressors, HVAC units) and variable torque loads (such as pumps, fans, etc). It can be used as a motor speed control and a phase converter.This item use Sine wave PWN(SPWM) for the control system.It is designed which also could use USA 60hz single phase input.Can work well with the Mach 3 controller.
  • Application: Spindle motor.CNC router, CNC machine, milling machine, drilling machine, wingding machine, mixer, extruder, slitter, winder, compressor, ventilator, pump, grinder, conveyor, elevator, centrifuger and other speed control machines.
  • If there are problems in use after you receive,please don't give us negative or natural feedback.Please contact us as soon as possible, we will help you solve problems or help you replace new one ..
Check Stock

Grizzly G9933 Three Spindle Shaper

  • Motor size: 3 H.P. TEFC Single Phase 220V.
  • Working size of table: 15-Inch x 32-Inch.
Check Stock

Grizzly Industrial G0791-12" X 36" Combination Gunsmithing Lathe/Mill

  • Lathe motor: 2 HP, 220V, single-phase, 8.5A.
  • Mill motor: 3/4 HP, 220V, single-phase, 4.5A.
Check Stock

Grizzly Industrial G0958-8" Combo Planer/Jointer with Helical Cutterhead

  • Motor: 1.5 HP, 120V/240V, single-phase, 15A/7.5A, prewired 110V.
Check Stock

6Pcs L298N Motor Drive Controller Board DC Dual H-Bridge Stepper Motor Control and Drives Module for Arduino Micro:bit Smart Car Robot UNO MEGA R3 Mega2560

  • ★L298N as main driver chip makes strong driving ability and strong anti-interference,dual-channel h-bridge driver working mode creates higher working efficiency,,drive stepper dc motors to work.to avoid damage the voltage stabilizing chip, please use an external 5v logic supply when using more than 12v.
  • ★Dual-channel H-bridge driver working mode creates higher working efficiency..
  • ★To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • ★Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • ★L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
Check Stock

Mophorn 1 Hp Electric Motor 3450 RPM 11.2-5.6 A Single Phase Motor AC 115V 230V Air Compressor Motor 56C Frame Suit for Agricultural Machinery and General Equipment

  • Single Phase: The motor is 1HP single phase electric motor, features with 115/230V voltage and 11.2/5.6A full load amperage.
  • Fitted Frame and Shaft: With 56C frame, the electric motor also has 1.875 inch length and 0.625 inch diameter keyed shaft.
  • High Speed: The electric motor features 3450RPM rated speed and 3600RPM synchronous speed. High speed meets your different needs..
  • Fan Cooled: Our electric motor is TEFC (Totally Enclosed Fan-Cooled) motor. A built-in fan helps to dissipate heat and prevent the motor from overheating..
  • Universal Motor: Universal Motor- Universal used for the matching of water pumps, agricultural machinery and general equipment..
Check Stock

Grizzly Industrial G9743-7" x 12" 1-1/2 HP Gearhead Metal-Cutting Bandsaw

  • Motor: 1-1/4 HP, 220V, 3-phase, 1725 RPM, 4.8 Amps with single-phase inverter.
  • Required power source: 220V, single-phase, 60Hz.
Check Stock

Gear Motor with Speed Controller AC110V 6W Electric Single-Phase Motor 1500PRM Variable Speed Reduction Gear Reducer Motor with High Torque (Reduction Ratio: 1:50)

  • 【STABLE OPERATION】The 6W geared motor can reach the speed of 27RPM, thus ensuring stable operation. The motor has low noise, long service life and flexible installation..
  • 【SPEED CONTROLLER】The single-phase motor also has a reduction gear box and a governor. The governor has a large torque and a variety of optional speeds. You can adjust the speed according to different products to achieve the desired effect..
  • 【MAIN PARAMETER】Rated voltage: AC110 V.
  • 6W geared motor:88 * 60 * 50mm / 3.4 x 2.3 x 1.9in (Appr.).
  • Reducer size: 43 * 60 * 50mm / 1.7 x 2.3 x 1.9in (Appr.).
  • 【WIDE APPLICATION】The geared AC motor has a built-in precision stator and pure copper coil, which is stable, reliable and fast in heat dissipation. It is widely used in packaging, printing, textile, food, construction machinery and other industries..
  • 【GUARANTEE】We are committed to providing you with high-quality customer service, please tell us if you receive our product with any unpleasure, we will try our best to help you as soon as we could..
Check Stock

Cafurty 1N4007 DO-41 Axial Silastic Guard Junction Standard Rectifier Diode (Pack of 20)

  • ☞ Model: MDQ-100A is designed for single phase Full wave rectification, which has four diodes connected in a one phase bridge configuration..
  • ☞ Max. Average Forward Rectified Current : 100A.
  • Production Size: 80 x 40 x 32mm/ 3.1" x 1.6" x 1.2" (L*W*T).
  • package content: 1 x rectifier bridge 1 net weight: 130g.
  • package content: 1 x rectifier bridge radiator.
  • ☞ Applications: DC power supply for instrument equipment , Input of PWM frequence converter rectifying power supply , Excitation power supply for DC motor, Input of switch power supply and auxiliary current Inverter current..
Check Stock

Make 1 Million Dollars

  • SUPERIOR SOUND. High-current EI transformer makes sure that sound quality doesn't suffer. Large custom audio capacitors and a discrete output stage..
  • AMP TECHNOLOGY. Wide Range Amplification Technology delivers high-current power stability via large custom capacitors, while low-NFB amps capture depth and spatiality for a wide frequency spectrum with low distortion..
  • AUTHENTIC AUDIO. Direct Mode bypasses tone and PM Bass circuitries. In combination with a refined amp circuit design, signal-pathlengths have been significantly reduced in comparison to the A-9010 for even more accurate and faithful sound..
  • BASS BOOST. Phase Matching Bass Boost eliminates phase-shift between low- and mid-range frequency bands. Bass response is enhanced without compromising vocal clarity, which is especially useful when playing music at low volumes..
  • FEATURES. 50 W + 50 W (4 ohms, 20 hz–20 kHz, 0.9% THD, 2-ch Driven, FTC). Remote controller..
Check Stock