ReviewsSliding Bushing

BXA #4 QUICK CHANGE HEAVY DUTY BORING BAR TOOL POST HOLDER 250-204

For use with BXA tool posts 250-200 or 250-222. 10-15" swing..
Equipped with a split bushing to accommodate a boring bar of smaller diameter. Holds 3/4" tool with bushing, 1" diameter without bushing.

Guide hole sizes are 1/4-Inch, 5/16-Inch, 3/8-Inch, 7/16-Inch and 1/2-Inch. Package induldes: Dowel jig x1.
Our jig is patented and easy to adjust ,and can be clamped on boards of different thicknesses(clamping wide capacity: 3/8" to 6"). Easy to install and use. Suitable for drilling and wood board joints, it is an ideal tool for panel furniture..
The steel block and clamping screw handle securely tightens the tools like a vise, and the fine thread spacing of screw handle provides uniform and stable clamping pressure for clamping the workpiece. The jig with rugged aluminum sides holding work securely without damage to the wood..
The drilling bushing is made of high-quality materials, with high strength and accurate positioning. When using a hand held drilling machinel, the countersunk drill bushing allows the drill bit to slide into the hole easily, ensuring the correct angle of the drill bit..
There are 4 holes along the top of the jig, only 2 of the holes accept threaded bushings(Replaceable 1/4" 3/8" 5/16").the other two holes accept 7/16" and 1/2" drill bits..

Includes One Mercedes Benz Bushing Remover/Installer.
Designed to Remove and Replace Metallic Bushings on Mercedes Rear Axles.
Services Almost All Mercedes Passenger Cars from 1984 and Up.
Features a Pressure Piece that Provides Correct Position of Replacement Bushing.
Includes a Cut-Out In Cap to Allow Sighting of Bushing Position.

For use with AXA tool post 250-100 or 250-111. up to 12" swing..
Equipped with a split bushing to accommodate a boring bar of smaller diameter. Holds 5/8" tool with bushing, 3/4" diameter without bushing.

【Application】This rear suspension bushing removal tool has a wide range of application and strong practicality. It is suitable for Ford Focus MK1 & MKII 1998-2007, Ford Cuga 2008, Ford C-Max 2007, Mazda 3 sedan, hatchback 2003-2008, suitable for Mazda 5 CR, CW, MPV 2005, applicable to V50 2004-2012, applicable to S40 MK sedan 2003-2012..
【Performance】This rear suspension bushing kit has excellent performance, protects your car from scratches, no marks or scratches, and is used to silently press in and pull out the rear of the shaft to improve safety and reliability..
【Easy to use】Designed for the removal and installation of bushes and bearings, this rear trailing arm bushing tool is easy to use and install without the need to remove the rear axle, saving a lot of time..
【Material】This control arm bushing removal tool is made of selected carbon steel. The greater the hardness, the higher the strength, but the lower the plasticity, the stronger the rust prevention, the longer the durability and the longer the service life..
【After-sales Service】This rear control arm bushing kit has been strictly tested before leaving the factory.If you encounter any problems in the use process, please contact our customer service in time, and we wil....

The New PS27 F/G-Nock bushing was designed for accuracy. This Bushing is designed to perform flawlessly after taking a beating in competition or practice..
This bushing will be longer lasting with less maintenance!! That means more time practicing and less time fixing arrows!!.
Made with 7075-T6 Aluminum to ensure every shot counts!.
Will accept both the F-Nock and M/G-Nock.

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

For use with BXA tool posts 250-200 or 250-222. 10-15" swing..
Heavy Duty Boring Bar Holder to holds 3/4" tool with bushing, 1" diameter without bushing.
Equipped with a split bushing to accommodate a boring bar of smaller diameter.
Precision ground and hardened. Completely sealed for maintenance free operation.

【High Quality Material】: The rear axle bushing is made of premium aluminum alloy material, which has high hardness and is solid, durable to use for long time and not easy to rust..
【Easy to Install】: The rear axle bushing is in reasonable size and lightweight, so it's easy and convenient to install and disassemble..
【Fit For】: The rear axle bushing is designed to fit for Wraith AX90018 90020 1/10 RC model toy car..
【Excellent In Toughness】: The material of the rear axle bushing is moderate in hardness and softness, excellent in toughness and good in protection..
【Guarantee】: If you are not satisfied with our product received, you can apply for unconditional return and refund within 180 days. In terms of any problem of this product, you can send emails as soon..