ReviewsSolid State Voltage Stabilizer

MYPIN® Universal Digital TA6-SNR PID Temperature Controller with Relay DIN 1/8 SSR-25DA and K type thermocouple,Dual Display for F/C,7 Output Combinations,Accuracy 0.2%

  • √ ● Dual display for Fahrenheit(F) and Celsius(C),Range: -1999 to 9999 (depends on the input signal).
  • √ ● Input: Thermo Resistor: PT100, Cu50,Thermocouple: K,Wre3 ~ Wre25 , Main Output: SSR: Open circuit: 4V, Closed Circuit: 24V 40mA DC.
  • √ ● K type thermocouple Temperature rang:0-800℃, Sensor Dia: 4.5mm, Cable Length: 2m.
  • √ ● Solid state relay SSR-25DA Load Voltage: AC 24-380V, Load Current: 25A, Input Voltage: DC 3-32V.
  • √ ● Packing details: 1 x SNR Temperature Controller( DIN 1/8), 1 x SSR-25DA Solid State Relay, 1 x K Type Thermocouple( 6 Feet).
Check Stock

HiLetgo 2pcs SSR-25DA 25A 250V Solid State Relay Module

  • SSR-25DA 25A 250V Solid State Relay Alloy Heat Sink.
Check Stock

AITRIP 1PCS 8 Channel 5V Solid State Relay Module Board High Level Trigger Compatible with Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC (1PCS)

  • Solid State Relay Module Board has been assembled, and electrical test passed.
  • Size: 155 x 55 x 24 mm (approximately 6.1 x 2.17 x 0.95 inch).
  • Has been assembled, and electrical test passed. Led indicator for each relay. Size: 155 x 55 x 24 mm (approximately 6.1 x 2.17 x 0.95 inch) Input control signal voltage: 0V - 0.5V Low stage (SSR is OFF), 0.5V - 2.5V (unknown state), 2.5V - 20V High state (SSR is ON).
  • Load voltage range: 75 to 264VAC (50/60Hz).
  • Load current: 0.1 to 2 AMP Standard interface that can be controlled directly by microcontroller (Compatible with Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Check Stock

DS18 3AVS 14.4V Car Audio Stabilizer Constant Steady Output Voltage

  • DS18 3 amp Volt stabilizer - input any voltage between 6-16v and get steady output at 14.4V..
  • Wide voltage input, steady output voltage @ 14.4V..
  • Strong performance, high reliability, & best preset voltage.
  • Input voltage range: 6-16v. Output voltage: constant 14.4V..
  • Voltage stabilized accuracy: 003c 0.5%. Ripple factor: 003c 0.1%. transfer efficiency: 003e 85%..
Check Stock

5 Pack LM2596 DC to DC Buck Converter 3.0-40V to 1.5-35V Power Supply Step Down Module

  • Input: DC 3 V to 40 V (input voltage must be 1.5 V higher than the output voltage, no boost).
  • Output: DC 1.5 V to 35 V voltage is continuously adjustable, maximum output current is 3 A.
  • Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed voltage (The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down).
  • Features: all use SANYO solid-state capacitors, 36 u thickening circuit boards, high-Q inductance with LED indicator output.
Check Stock

[2 Pack] DC-DC 5A Buck Converter 4-38V to 1.25-36V Step-Down Voltage Regulator High Power Module with LED Display

  • 【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects..
  • 【Input Voltage】DC 4V to 38V (input voltage must be 1.5V higher than the output voltage, no boost)..
  • 【Output Voltage】DC 1.25V to 36V voltage is continuously adjustable, maximum output current is 5A..
  • 【Mini Size】62*38*14 mm (with potentiometer). 2 sets included..
  • 【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V).
Check Stock

uxcell ASH-25DA Solid State Relay 4-32VDC to 24-480VAC 25A Single Phase SSR DC to AC Relay

  • Total Size: 72 x 43 x 90mm/ 2.83'' x 1.70'' x 3.5'' (L*W*H).
  • Package Content: 1 x Solid State Relay, 1 x Heat sink.
Check Stock

Valefod 10 Pack DC to DC High Efficiency Voltage Regulator 3.2-35V to 1.25-30V Buck Converter DIY Power Supply Step-Down Module

  • 【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects..
  • 【Input Voltage】DC 3.2V to 35V (input voltage must be 1.5V higher than the output voltage, no boost)..
  • 【Output Voltage】DC 1.25V to 30V voltage is continuously adjustable, maximum output current is 3A..
  • 【Mini Size】45 * 23 * 14 mm (with potentiometer). 10pcs included..
  • 【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V).
Check Stock

Valefod 6 Pack LM2596 DC to DC High Efficiency Voltage Regulator 3.0-40V to 1.5-35V Buck Converter DIY Power Supply Step-Down Module

  • 【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state....
  • 【Input Voltage】DC 3V to 40V (input voltage must be 1.5V higher than the output voltage, no boost)..
  • 【Output Voltage】DC 1.5V to 35V voltage is continuously adjustable, maximum output current is 3A..
  • 【Mini Size】45 * 23 * 14 mm (with potentiometer). 6pcs included..
  • 【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue....
Check Stock

AUTOGEN 2-Bank Marine Battery Charger 10-Amp 5-Amp Per Bank Dual Battery Trickle Charger Maintainer 6V & 12V Onboard Battery Charger and Battery Maintainer

  • 【2-Bank, 10-Amp】10 Amp (5 Amp per bank) on-board battery charger for charging and maintaining two 6V/12V batteries independently..
  • 【Widely Batteries】Safely charge and maintain all types of Lead-acid batteries, including wet, gel, AGM, and deep-cycle batteries. Marine battery....
  • 【Automatic Voltage Detection】Auto select 6V/12V mode without keying button, it automatically determines the correct voltage for your target....
  • 【Monitor Power Levels】Solid state two-color LED light indicates the state of the charge. Continuous charging, unlimited time, automatically enter....
  • 【Multiple Security Protection】Multiple security protection, such as over current protection, overcharge protection, overheat protection, reverse....
Check Stock

Dorhea 7PCS LM2596 DC to DC Buck Converter Voltage Regulator 3.0-40V to 1.5-35V Buck Converter DIY Adjustable Power Supply Step Down Module

  • The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can....
  • DC 3V to 40V (input voltage must be 1.5V higher than the output voltage, no boost)..
  • DC 1.5V to 35V voltage is continuously adjustable, maximum output current is 3A..
  • The LM2596 buck module input and output interface can not be reversed. The input voltage must be higher than the output voltage..
  • Steps: connect to power source, adjust the swirl button on the blue potentiometer and monitor voltage with multimeter to get the needed....
Check Stock