ReviewsSpi Servo Board

BIGTREETECH SKR V1.4 Turbo Control Board 32bit for 3D Printer Compatible with TFT35 E3 V3.0.1/TFT70 Touch Screen Support TMC2209/TMC2208/TMC5160/TMC2130 for Most FDM 3D Printer (with 5*TMC2209)

  • ✨BIGTREETECH SKR V1.4 Turbo using 32-bit 120MHz ARM-class Cortex-M3 series LPC1769 main control chip, the performance is greatly improved..
  • ✨SKR V1.4 Turbo control board can supply power to TFT screen, BLtouch, Neo-pixel by plugging in an external DC5V power module.
  • in addition, I2C, SPI, WIFI interface is reserved to facilitate customer DIY..
  • ✨On-board TMC-driven SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap..
  • ✨Compare to other stepper motor driver in the market, our TMC2209 silent stepper driver generate lower heat and it has a large-area cooling position to lower the temperature. It driver can lower 30% heat than others stepper motor drivers even working last for a long time. With Passive cooling on a 10 hours print, they only hit 37℃..
  • ✨BIGTREETECH TMC2209 V1.2 is an ultra-silent motor driver IC for two-phase stepper motors, which adopts stealthChop2 Mute technology which reduces motor noise ....
Check Stock

SparkFun MicroMod ATP Carrier Board-Modular Interface Ecosystem-Connect microcontroller/Processor Board to Various Carrier Board peripherals

  • Access all the pins (i.e. ATP) of the MicroMod Processor Boards with the SparkFun MicroMod ATP Carrier Board! This board breaks out the MicroMod Processor Board's pins on the M.2 connector to 0.1" spaced female headers and PTH pads on the edge of the board..
  • Features: M.2 Connector. Operating Voltage Range: ~3.3V to 6.0V (via VIN to AP7361C 3.3V Voltage Regulator). 3.3V (via 3V3).
  • Ports:1x USB type C, 1x USB type A Host, 2x Qwiic Enabled I2C, 1x CAN, 1x I2S, 2x SPI, 2x UARTs, 2x Dedicated Analog Pins, 2x Dedicated PWM Pins, 2x Dedicated Digital Pins, 12x General Purpose Input Output Pins, 1x SWD 2x5 header. Note: Depending on the design of the Processor Board, not all the pins may be accessible..
  • Additional Features: 1mAh battery backup for RTC. Buttons: Reset, Boot, LEDs. Power. 3.3V. Phillips #0 M2.5x3mm screw included.
  • Carrier board only. MicroMod processor board will be needed to use..
Check Stock

ACEIRMC 2pcs ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 with Camera Module OV2640 2MP for Arduino (4pcs)

  • The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core.
  • ESP32-CAM WiFi Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card.
  • Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
  • Support OV2640 and OV7670 cameras, built-in flash.
  • Support image WiFi upload and Support TF card.
  • Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
  • Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module.
Check Stock

Raspberry Pi Pico With Vilros Keychain Carrying Case

  • The Pico is a low cost, high performance microcontroller board built around the Raspberry Pi RP2040 chip Dual core ARM Cortex M0+ processor at up to 133MHz with variable core frequency 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC and 16x controllable PWM channels.
  • Includes Vilros Picoboat Keychain Carrying Case.
Check Stock

Raspberry Pi Pico With Vilros Keychain Carrying Case

  • The Pico is a low cost, high performance microcontroller board built around the Raspberry Pi RP2040 chip Dual core ARM Cortex M0+ processor at up to 133MHz with variable core frequency 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC and 16x controllable PWM channels.
  • Includes Vilros Picoboat Keychain Carrying Case.
Check Stock

KEYESTUDIO Microbit Sensor Breakout Board V2 I2C SPI Micro USB for BBC Micro:bit

  • Particularly design this keyestudio sensor expansion board V2 for micro:bit. breaks out all the PIO ports on the micro:bit control board into 3PIN interface (GND, VCC, Signal), easy to connect it with other sensor modules..
  • Extending some commonly-used serial communication interfaces into pin or female headers with 2.54mm pin pitch, such as I2C and SPI communication pins.Allows communication between micro:bit control board and other communication devices..
  • Two kinds method to power the micro:bit board, through a black DC jack (DC 7-9V) or a mciro USB port (DC 5V) on the shield..
  • Connection Diagram, Sample Code, Using Method and Resources are provided in our wiki page. Technical support is available via email or message..
  • Solder is very clean, everything is aligned nicely, all boards are well packed after function, voltage, current testing, protected in a beautiful box. Up to FCC and CE Standard: made from environmentally friendly components and materials..
Check Stock

1.5inch RGB OLED Display Module, 128x128 Pixels 16-bit High Color (65K Colors) SPI Interface Compatible with Arduino Raspberry Pi Jetson Nano STM32

  • This is a general 1.5inch RGB OLED display module, 128x128 pixels, 16-bit high color (65K colors),clearly displays colorful images, with embedded controller, communicating via SPI interface..
  • Driver: SSD1351. Display color: RGB, 65K colors.
  • Supports 4-wire SPI OR 3-wire SPI interface, configured via onboard resistor.
  • Dimension: 44.5 x 37 (mm),Operating voltage: 3.3V / 5V,Viewing angle: 003e160°,Interface: 4-wire SPI, 3-wire SPI.
Check Stock

eleduino BeagleBone Black Rev C (4G) Single Board Computer Development Board

  • 4GB 8-bit eMMC on-board flash storage (rev. 3).
  • Provides lots of expansion interfaces such as Ethernet, USB host and OTG, TF card, serial, JTAG (no connector by default), HDMI D type, Emmc, ADC, I2C, SPI, PWM and LCD.
Check Stock

Bus Power

  • Super material: It is made of electronic accessories, nickel plating on surface(anti-oxidatioan), inner conductor: pure copper.it is long lasting and durable for you to use..
  • Package including: Include 5pcs of MCP2515 Development Board. This version of the MCP2515 Breakout solves some of the board's problems. 120 ohm terminal resistors. With Impedance matching, ensures the drive capability, long distance data transmission prevents signal emission.
  • High Power High Efficiency: Supports CAN V2.0B specification, the communication speed 1Mb/s. High reliability, strong vibration resistance, good electromechanical performance. 0 to 8-byte data field. With standard frame, expand the frame and remote frame..
  • Main specification: The MCP2515 module is 5V DC power supply, SPI interface protocol control. Working current is 5mA (1 microamp standby current. Except the power indicator).
  • A wide range of applications: It is suitable for home smart devices, industrial wireless control, wireless monitoring, wireless identification, wireless positioning system signals and other applications..
Check Stock

Arduino Uno 3 Ultimate Starter Kit Includes 12 Circuit Learning Guide

  • This is the ultimate Arduino Uno kit enough to get you started with hundreds of arduino projects.
  • Bread Board — Holder — Jumper Wires — USB Cable — LEDs — DC Motor — Small Servo — Relay.
  • Includes a total of over 190 electronic parts and components.
Check Stock

AITRIP 3pcs Multi-Function Shield ProtoShield Multi-Functional Expansion Board Sensor Shield Module with Four Digital Display Compatible with Arduino

  • 4 LED lights (LED indicator to know the importance of doing in the actual project, with this indicator can work directly with the program status indicators for easy debugging..
  • AITRIP 3pcs Multi-Function Shield ProtoShield Multi-Functional Expansion Board Sensor Shield Module with Four Digital Display Compatible with Arduino.
  • Four digital (using 74HC595 driver provincial IO learning SPI), you can do digital display test (can display temperature, voltage, counter value, etc.)..
  • Expansion board directly connected with LD3320 non-specific voice recognition module, you can achieve voice control..
  • Expansion board directly with the SG90, MG945 MG995 and other steering gear connected to achieve the robot and other complex actions..
  • Expansion board directly with the SYN6288 free voice module docking,it can achieve voice broadcast function..
Check Stock