ReviewsSpiral Point Tap And Reamer Set

Irwin Tools Tap and Drill Sets, 13-Pieces

This tap and drill bit set produces a thread that is strong and easy to tap.
High-carbon steel plug taps are great for general-purpose threading.
135° split-point drill bits give fast, precise drilling.
Set pieces: 6 – 32 NC, 8 – 32 NC, 10 – 24 NC, 10 – 32 NF, 12 – 24 NC and 1/4″ – 20 NC plug taps and 7/64″, 13/64″, #29, #25, #21 and #16 drill bits, plus a T-handle tap wrench.

Self-feeding spiral design for extra-fast and easy hand reaming.
Suitable for hand reaming on pipe, sheet metal or for enlarging conduit box outlets.
The model 2-S reamer is not suitable for power reaming.
Pipe reamer has a 1/4-inch to 2-inch (6 mm to 50 mm) pipe capacity.

...w it firmly into the newly tapped head.
Apply grease on the tap to help catch any metal shavings (rather than letting them drop into the cylinder) and back out the tap out every half turn to every whole turn to clean the metal shavings from the tap.
PERFECT SIZE: 14mm reamer with 12 points.
Use with 3/8-inch drive ratchet or wrench.
Inserts sizes are 3/8-Inch, 7/16-Inch, 1/2-Inch, and 3/4-Inch.
Tap is tapered to allow the tip to fit and rethread the hole in order for the coil to fit.
Measure your plug diameter, thread, and pitch to see if this kit is compatible.
PACKAGE CONTENTS: Rethread kit includes a tapping reamer and 4 different depths of inserts for your convenience.

Spiral point tap pushes chips ahead of tool to reduce clogging.
Spiral point with straight flutes for cutting threads in through holes.
Non-relieved design for applications requiring close gauging fits, for manual feed rate applications, or for use on older equipment.
Produces ANSI standard right-hand threads in metric sizes.
Plug chamfer for easier starting and correct perpendicular alignment.

Product Name: CAIDU 5pcs HSS 6542 Titanium Coated Spiral Flute Metric Taps Set M3 M4 M5 M6 M8.
✔ Type Size: M3: 3 mm * 0.5 , M4: 4 mm * 0.7 , M5: 5 mm * 0.8 , M6: 6 mm * 1 , M8: 8mm * 1.25.
✔ Material: HSS 6542 Titanium coating, cutting will not be left. Have good machinability. High hardness, fast cutting, wear high temperature.
✔ Spiral groove is reduced to remove crumbs, not easily broken tap. Tap the crumbs into a spiral up chip evacuation, it is more suitable for the processing of blind holes and Sticky materials processing.
✔Applicable Workpiece: tensile strength 750N / mm 2 or less the low-carbon steel, copper, aluminum, hardwood, plastic.

Tap shoots chips ahead of the cutting action reducing loading and clogging in the flutes.
They are recommended for use in through or blind holes.
Allow for chip accumulation in the bottom of the hole.
Ideal for threading a wide variety of ductile materials, copper and copper alloys, brass and non-metallics.

⭐【Material】The Adjustable Reamer is made of premium HSS with good hardness and toughness..
⭐【Square End】Square end allows the user to turn the reamer by hand with an adjustable wrench or straight handle tap wrench..
⭐【How to Adjust】Blades are adjusted by loosening one nut and tightening the other..
After reaming the hole can get the exact size and shape..
⭐【Applicable Material】A3 steel, alloy steel, cast iron, cast steel, aluminum and other metal materials..

Straight flute reamers should be used in thru-hole applications only.
Blades are adjusted by loosening one nut and tightening the other.
Adjustable blades give the operator the ability to handle multiple hole sizes with a single tool.
Square end allows the user to turn the reamer by hand with an adjustable wrench or straight handle tap wrench.

The heavy duty high-speed steel bridge reamer is also called construction reamers,it used for aligning an existing hole and enlarging undersized hole prior to bolt or rivet installation.Our reamer bit aligns and enlarges pre-drilled holes ready for bolting..
Makes reaming holes out extremely easier than using large drill bits,the reamed hole is smooth without tear-outs. But there must be a existing hole or a pilot hole that is smaller than 5/8" before using our 5/8" Bridge/Construction Reamer..
The tapered point design permits the reamer bit to enter into the overlapping holes of out-of-line,make the bolt holes line up.Enlarging the holes in the steering knuckles and pitman arm..
The 5/8" bridge reamer bit is not a drill bit,only aligning reamer to aligh holes which are pre-drilled.If you need to expand a hole to 5/8". At first there must be a 3/8" pre-drilled hole,then ream out to 5/8"..
Commonly used in bridge,construction,steel erection and automotive truck trailer industries,specially use in structural materials such as steel, metal, alloy aluminum,brass,plastic,iron,nickel,copper,cast iron etc.Three symmetrically placed flats on shank provide positive grip in portable electric and pneumatic tools..

【High working efficiency】: This chucking machine reamer set has sharp cutting-edge, high efficiency cutting ability, high accuracy, so your work will become easier under the use of this tools set. Also, this set has a long-term using service life.
【High quality materials】: This set of cutter milling reamer is made of high quality and high speed steel materials, so these reamer cutters have high hardness.
【Specific and professional use】: This steel milling cutting tool set is designed for reaming to mold processing and handicraft processing.
【Wide using range】: This whole chucking reamer set can be widely used for bore machining, installed in drilling machine, milling machine, etc.
【Fine process】: This set of chucking reamer tools' surface has processed by iron, plastic, wood, copper, aluminum and other soft materials.