ReviewsStepper Motor Feeding System

Dr.Roc Compatible Instrument Cluster Gauge Stepper Motor Repair Kit Fits X27 168 03 to 06 with 7 Stepper Motors Soldering Iron Solder Sucker Chevy Silverado GM GMC

• The latest generation,Premium stepper motor,quiet operation and reliability,Perfectly Replace for the older and faulty XC5-168( XC5168 ), X15-168( X15168 ) ,X25-168 ( X25168 ) and X27-168 ( X27168 , X27.168 , X27 168 ) stepper motor that came in your vehicles,Use the tool on the upper left corner to check whether this product fits your vehicles.
• Stepper motor is used for repairing guage cluster,including speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery voltage gauge, water temperature gauge or fuel gauge.
• Solve the common problems of your vehicle such as, gauges cluster dead,chatter,sticking,false/jumpy/inaccurate readings,pegged out to the left or right of the dial, ratchet up or down,sticky needle movement,erratic gauge movement etc.
• Each gauge of your instrument cluster need one stepper motor.Since one stepper motor went out,and it will result all other stepper motors go out soon. Checking the quantity of stepper motors for your vehicle to decide to buy the 6 or 7 one.It is easy to use for upgraded adjustable soldering iron,but you’d better to search the instructions Video on Internet first,which is very helpful..
• The premium instrument cluster repair kit is compatible with Silverado,Suburban,Traiblazer,Tahoe,Avalanc....

Saiper Flexible Couplings 5mm to 8mm (5pcs) Aluminum Alloy Joint Connector Compatible with NEMA 17 Stepper Motors, RepRap 3D Printer or CNC Machine, 3D Printer Accessories

• Fully assembled & tested, no soldering required, Can be extended to control other accessories..
• It has Cartesian robots and requirements of the extruder, Heated bed control with additional 11A fuse. Fits up to 5 stepper driver board..
• Three field effect transistors, three heater / fan output ports, three thermistor circuits.A number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack..
• The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.Pololu board foot socket, can be easily replaced or removed..
• The modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion..

Twotrees Stepper Motor Driver, TB6600 4A 9-42V Nema 17/23 CNC Controller Single Axes Hybrid - Upgraded Version

• 【1】Package included: 1 x Stepper Motor Driver,1 x Stepper Motor, 1 x Wire..
• 【2】Suitable for a wide range of stepper motors from NEMA size 17,23 and 24 (42 * 42mm to 60 * 60mm). It can be used in various types of machines, such as XYZ tables, labellers, laser cutters, engraving machines, pick-place devices and so on..
• 【3】Motor driver: 9V-42V DC power supply, H-bridges bipolar constant phase current drive. The maximum 4.0A of the eight types of output current..
• 【4】The largest 32 divisions of the 6 models are optional.
• Suitable for 4 wires, 6 wires and 8 wires stepper motor..
• 【5】Protect form: Overheated protection, overcurrent protection, undervoltage protection, prevention of inversion..

CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine Control Board CNC Router Engraver Milling Machine Controller Board

• ♞【Model】Upgraded 3 Axis GRBL 1.1F USB Port GRBL Control Board.
• ♞【Support software】GRBL Contol/Candle(3 axis)/Universal Gcode Sender.
• ♞【Support Motor】Support XYZ three-axis control, spindle.Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor Nema17,Nema23).
• Support spindle: Support 24VDC Spindle PWM speed (0%-100%),also support 3-pin PWM/TTL signal control module.
• ♞【New functions】Add 2-pin emergency stop button port,probe port,XYZ limit port and add the power button switch..
• ♞【Applications】 The control board can be used with the 1310,1610-PRO, 3018,3018-PRO and 3018-PRO MAX etc engraving machines..

Worm Gear Nema23 Stepper Motor 3.5A L2.1inch Gearbox Ratio 30:1 Speed Reducer for CNC DIY Router

• 2 phase stepper motor 2.1inch long, 1.3Nm.
• Speed reducer motor output speed 0--20 R/min.
• Applied to CNC Router, Engraving, Milling, Lathe. Fast Delivered 4-6 days after shipping..

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

• 5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
• Stepper motor with a standard interface could be connected with Driver Board easily.
• A, B, C, D four-phase LED indicates the status of the stepper motor work..
• 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
• Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.

RAMPS 1.4 Controller + MEGA2560 R3 Board + 5pcs Soldered A4988 Stepper Motor Drivers + 5pcs Heat Sinks + 19pcs Jumpers with USB Cable for RepRap 3D Printer Kit

• SAVING SPACE: The RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package. So it can save space and cost..
• SCALABLE: RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion. A number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack..
• EASY TO USE: Using the bootloader, you can download the program directly via USB without using other external writers. Development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works..
• MODULAR DESIGN: The modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion..
• POWER SUPPLY AND DRIVER: Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil..

Nema23 57 Stepper Motor Mount bracket Support Clamp Aluminium Alloy Mounting Holder for CNC Router Milling Engraving Machine

MybotOnline 5 Sets Stepper Motor 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board

• Stepper motor with a standard interface, motor diameter: 1.1", wire length: 9.05".
• A, B, C, D four-phase LED indicates the status of stepper motor work.
• Compatible with ArduinoIDE UNOR3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi.
• Gift: 1x 10-pin male to female multicolor breadboard jumper wires，each cable length: 7.87"(20 cm).
• Packing in a box: 5 sets Uln2003 stepper motor + driver board + 10 pin jumper wire.

diymore 5-Set DC12V 28BYJ-48 Stepper Motor with ULN2003 Drive Boards Blue(12V)

• Stepper motor driver board with ULN2003..
• A, B, C, D four-phase LED indicates the status of the stepper motor work..
• Stepper motor with a standard interface, when used directly pluggable..

MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board Controller Card for CNC Engraving Servo Motor Stepper Motor Servo motor

• 【Functions】The function of this motion control card includes that it supports automatic probe tool, emergency input, limit switch, and supports....
• 【4-axis Linkage】Usb interface board supports for 4-axis linkage, you can connect four stepper motor drives or servo drives. 4 general-purpose....
• 【Wide Use】The maximum step-pulse frequency of motion control card is100KHz, which is very suitable for CNC Engraving, Servo Motor, Stepper Motor....
• 【Advantage】The motion controller needs using external 24V DC power to isolate USB and external port, and to make the system more stable. And it....
• 【Drive Output Interface】The 4 general-purpose isolated relay drive output interface can drive four relays for controlling the spindle starts,....