ReviewsTable Saw Fence Accessory

WoodRiver Adjustable Fence Clamps, 2 Piece

  • This fence will improve your band saw instantly. Easy to adjust for blade lead with angle bracket design. Will fit most 14" band saws with tables up to about 16" square..
  • Bolts directly to existing holes in the 14" Delta, Jet, Ridgid, Powermatic (without extension table) & Porter Cable. May be able to be attached to other 14" band saws by drilling four holes, see instruction sheet..
  • The most rigid fence available. Two separate fence position locks at both ends and two separate blade lead locks as well..
  • See the HD Band Saw Circle Jigs - 7286-7290 too. Clamps to any band saw to cut circles or arcs from 3" diameter up to 189.
Check Stock

Shop Fox W1837 10\ 2 hp Open-Stand Hybrid Table Saw

  • SAWSTOP PATENTED SAFETY SYSTEM: Stops a spinning blade on contact with skin. The blade stops in less than 5 milliseconds, and drops below the table, minimizing a potentially life-altering injury to a mere scratch..
  • UNMATCHED QUALITY: The trunnion and arbor are built for precision, strength and stability. Poly v-ribbed belts reduce vibration and help ensure a great cut. Table flatness is measured diagonally at 0. 010” maximum gap..
  • RELIABILITY: The Control Box houses the on-off switch, power paddle, and on-board computer, and constantly checks that all systems are working to reliably keep you safe..
  • CONFIGURABILITY: Over 150 unique configurations, makes the Contractor Saw the most configurable SawStop saw. Adding a mobile base, sliding crosscut table or router table, are just a few of the ways to make this your ideal saw..
  • UNIVERSAL PERFORMANCE: The Contractor Saw offers versatility, reliability and safety for a variety of users. The cast iron table top (Cast Iron Wing Assembly, CNS-CIWA, sold separately) creates a better-than-hybrid performance in the shop at an affordable price..
  • 36-INCH T-GLIDE FENCE ASSEMBLY: The 36-inch T-Glide Fence & Rail are made of heavy-gauge steel for sure lockdown and reliably square cutting for years without deflection..
Check Stock

Husqvarna K4000 Cut-N-Break Saw Orange

  • [SETS UP IN SECONDS] Take this table saw to the job site or move it around the workshop. There’s even a built-in carry handle.
  • [CUTS LIKE A FULL-SIZE] With the standard guard and riving knife system you can perform rip, cross, scroll, and miter cuts.
  • [TOOL-LESS BLADE CHANGE] Uses any brand’s standard 4” T-shank blade, but we threw 5 in the box to get you started cutting wood, ceramic tile,....
  • [0-60° MITER CUTS] With the adjustable gauge you can pull off precise miter cuts for a whole assortment of woodworking projects.
  • [ON-BOARD ACCESSORY STORAGE] When the miter gauge, rip fence, and extra blades aren’t in use they can be conveniently housed in the base of the saw.
Check Stock

SAWSTOP 10-Inch Contractor Saw, 1.75-HP, 30-Inch Standard Fence Assembly (CNS175-SFA30)

  • SAWSTOP PATENTED SAFETY SYSTEM: Stops a spinning blade on contact with skin. The blade stops in less than 5 milliseconds, and drops below the table, minimizing a potentially life-altering injury to a mere scratch..
  • RELIABILITY: The Control Box houses the on-off switch, power paddle, and on-board computer, and constantly checks that all systems are working to reliably keep you safe..
  • CONFIGURABILITY: Over 150 unique configurations, makes the Contractor Saw the most configurable SawStop saw. Adding a mobile base, sliding crosscut table or router table, are just a few of the ways to make this your ideal saw..
  • UNIVERSAL PERFORMANCE: The Contractor Saw offers versatility, reliability and safety for a variety of users. The cast iron table top (Cast Iron Wing Assembly, CNS-CIWA, sold separately) creates a better-than-hybrid performance in the shop at an affordable price..
  • 30-INCH STANDARD FENCE ASSEMBLY: This aluminum fence assembly is engineered for the ideal balance between lightweight utility and accurate lockdown..
Check Stock

Rockler Double Featherboard

  • 4-Piece Wood Router Table Accessory Kit: Get a cleaner shop and safer, more consistent routing with this convenient Rockler router table accessory kit! Our 4-Piece Router Table Accessory Kit includes a dust port & 3 featherboards for more consistent cut quality and to help prevent kickback..
  • 3 Featherboards For Consistent Cut Quality: Two of the router featherboards mount to the fence, exerting pressure down toward the table, while the third mounts to the router table and keeps your work against the fence..
  • 2-1/2 Dust Port: Keep your router table clean and dust-free with our router dust port. This router fence dust port has a 2-1/2'' OD (2-1/4'' ID) hook-up..
  • Easy To Use: This miter slot featherboard can be quickly and easily connected to a miter slot openings of 3/8” deep x 3/4" wide or without the need for additional hardware..
  • What’s Included? Our 4-Piece router table accessory kit includes an easy-mount dust port, plus three featherboards for more consistent cut quality and to help prevent kickback..
Check Stock

Woodworking Thin Board Cutting Guide Tools, Thin Table Saw Jig Fast Cutting Limit Thin-Rip Tablesaw T Track Adjustable Positioning Fixing Tool for Cutting Thin Board Table Saw Router Table Band Saw

  • ❣ MOST STABLE AND CONVENIENT TO USE: The table saw accessory that delivers consistent thin strips without binding, burning or kickback. The Thin Rip Guide works on the offcut side of the blade, making it much safer than methods where the strip is between the saw blade and the fence..
  • ❣ EASY TO USE: Woodworking table saws jig are easy to use and work on most table saws. Positioned on the off-cut side and a few inches in front of the blade, the table saw jip provides a bump stop that delivers consistent dimension strips. It uses a pair of bearings for the contact point. Easily calibrated scales in both inch and metric graduations make it simple to get just the size you want for your strips..
  • ❣ WIDELY USE: From portable job site saws to large cabinet shop saws, the thin table saw jip guide works with any saw that has a 3/8 ” x 3/4″ miter slot with a “T” profile. Strips as thin as 1/32″ and up to 1-1/4″ can be cut, depending upon the spacing between the miter slot and the blade..
  • ❣ DURABLE MATERIAL:The body of the woodworking thin board cutting guide tools guide is machined from a solid billet of top-quality aluminum and anodized for corrosion protection. All other components are either stainless steel or other corrosion resistant m....
Check Stock

Fulton Precision Miter Gauge with Aluminum Miter Fence with 45 degree Angled Ends for Maximum Stock Support and a Repetitive Cut Flip Stop

  • The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs..
  • The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place..
  • The head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a met....
Check Stock

Rockler Table Saw Small Parts Sled

  • Sled base and fence provide zero-clearance support—just run it through your saw to locate the kerf.
  • Sled rides in miter track of your table saw—included miter slot stop limits forward travel of sled.
  • Rear-mounted blade guard is adjustable to fit most table saws.
  • Aluminum T-track on top edge of fence lets you add a flip stop (not included) for repeatable cuts.
  • Short T-track parallel to blade accepts an optional T-track hold-down clamp (sold separately).
Check Stock

DWE7402DI Dado Throat Plate, Table Saw Parts Insert Accessories Replacement for 10-Inch Portable Table Saw DEWALT DWE7490, DWE7491 Versiones

  • ❤ [A good helper for table saws] If you have a table saw and need to cut at any angle, then you will know the value of a miter gauge. You may also know that the miter gauge that comes with the saw is not very accurate or durable. Not to mention the fit in the miter groove may not be so good. And our high-quality miter gauges can meet your table saw cross-cutting needs..
  • ❤[High-quality material] The guide rod and baffle of the table saw miter gauge are made of all aluminum to ensure its durability and firmness, rust and wear resistance, and the table saw miter gauge fence is made of aluminum alloy die-casting, which has better accuracy. high..
  • ❤[With clamp] The table saw miter gauge is composed of a miter gauge clamp, a material baffle, and an angle push plate. The clamps can be adjusted by screws to fix different cutting objects, which is not possible with other mitre gauges without a holder. The bottom of the mitre gauge is equipped with a 5/8 groove for the mitre gauge, and the all-aluminum slide bar slides smoothly ..
  • ❤ [Easy to operate] The miter gauge is cut at a precise angle of 60° on both sides with pointers. If you need to adjust the head, you only need to loosen the column knob and rotate the head to the desired position, so loosen th....
Check Stock

TUFFIOM 10inch Table Saw w/Port for Connecting Dust Collector, Portable Benchtop Table Saw w/ 60T Blade, Stand & Push Stick, 5000RPM, Adjustable Blade Height, 90°Cross Cut & 0-45°Bevel Cut

  • ADJUSTABLE BLADE ANGLE & HEIGHT: With hand wheel for blade height adjustment, the blade height of the table saw can be adjusted to meet your specific needs. What’s more, the blade angle can also be adjusted to provide 90°cross cutting and 0-45°bevel cutting. And it features 60T blade which can yield a smoother cut..
  • PORT FOR DUST COLLECTOR: The 10inch table saw is designed with port for connecting dust collector at the back (Note: It does not come with dust collector), which can help create a cleaner working environment. And it is also designed with storage part at the left and right sides for storing wrenches and push stick when they are not in use..
  • POWERFUL PERFORMANCE: The no load speed of the table saw is 5000RPM, which allows it to cut most wood with ease. And triangle supports at the back of the metal stand improves the stability of the table saw. Besides, extensions on both sides of the table top also allows it to handle a larger piece of wood more stably than those without extensions..
  • RIP FENCE & ANGLE STOP FOR PRECISE CUTTING: Designed with self-aligning rip fence with parallel guide, the portable table saw can deliver a more precise cutting. And its angle stop can help you to adjust the wood to the appropriate cutting angle..
Check Stock

Fulton DIY Table Saw Crosscut Sled Kit with 2 UHMW Bars 2 Aluminum Tracks 1 Knob and 1 Bolt along with Full Color HOW TO BUILD YOUR OWN Crosscut Sled Guide Booklet

  • If you own a table saw, you probably have come across a situation or two where you need to make smaller cuts or make cross cuts. You may also have had the need to make repetitive cuts of the same length. Making small cuts, cross cuts and repetitive length cuts is where table saw crosscut sleds excel. Crosscut sleds help stabilize the work piece and are very accurate since they are essentially calibrated to your saw during the sled building process..
  • Some time ago we noticed a lot of companies had UHMW bars available for purchase. While we as a woodworking company know exactly what they are used for, many novice or non-woodworkers do not. That’s when we decided to create this package with pre-cut UHMW bars, pre-cut aluminum track, a knob and bolt and an easy to understand how to guide booklet so you can create your very own, custom crosscut sled to fit your table saw!.
  • UHMW bars are most commonly used as runners for crosscut sleds since they don’t produce as much friction as wood does. Another advantage is that UHMW won’t expand or contract like wood does during drastic weather changes. Each bar is approximately 3/4” x 3/8” which fits most standard table saw slots. UHMW bars are also slick and won’t leave any residue, dust or shavi....
Check Stock