ReviewsTaper Roller Bearing Puller

ABN Front Wheel Drive Axle Pulley Attachment - CV Axle Removal Tool CV Joint Slide Hammer Adapter

Use lubricant fluid for added ease (not included).
[Safe for Your Vehicle] Unlike pry bars or CV axle fork tools, the CV shaft slide hammer axle attachments focus the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
Pulls CV joints on 1986-current Taurus/Sable.
[Built to Last] Heat-treated CV puller adapter with black oxide finish ensures optimal strength and durability while resisting rust and corrosion.
Inner CV axle removal tool has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.

Check Stock

ATPEAM 3 Jaw Inner Bearing Puller, Jaw Pilot Bearing Puller Auto Bushing Gear Extractor Wheel Bearing Puller Heavy Duty Automotive Machine Tool Kit for Car SUV

3-Jaw Puller Set: Ideal for Automotive flywheel, Motorcycle wheel, Bicycle wheel, Pump bearing generator bearing, Machine bearing etc.
Premium Material: The 3-Jaw Bearing Extractor Puller is made of strong carbon steel with black Oxide finishing, high hardness, corrosion-resistant forged and heat treated steel jaws, can serve for long time.
Strong Puller Power: Structure design, gently turning the small wrench can produce a strong pull force.Removes all sleeve-type bearings with 1/2-2inside diameter..
Stable & Safe: The Blind Bearing Puller applies even pressure to preventing damage to bearings, also ensures stability during use.
Package Included: 1x 3-Jaw Inner Bearing Puller Tool. Size: 200x135mm. Wire rod length: 175mm. Bar length: 125mm. Arm length: 86mm..

Check Stock

DURATECH 3-Piece 3-Jaw Gear Puller, 3\

Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 4 or 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas. Achieve more with its adjustable and reversible jaws..
Use the DURATECH 3, 4, 6-Inch Gear Puller 3 Jaw Flywheel Puller Set to remove most shift-fitted parts with ease. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free....

Check Stock

Orion Motor Tech 3\ 4\ 6\ 8\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels

Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
Better Together: This professional or home tool kit includes four puller sizes to cover most applications: a 3 inch gear puller with a 4.3" max. reach and 3" max. spread.
a 4 inch gear puller with a 5" max. reach and 4" max. spread.
a 6 inch gear puller with a 7.3" max. reach and 6" max. spread.
and an 8 inch gear puller with a 9.3" max. reach and 8" max. spread..
Versatile Design: Each of the three smaller 3-jaw gear and bearing pullers can be reversed to pull parts from the inside or outside.
the 8 in. puller can be used in 4 different positions to deal with both medium and large parts..
45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that th....

Check Stock

8MILELAKE Rear Axle Bearing Puller Extractor Installer Set Axle Bearing Removal Remover Tool Kit

[APPLICATION]: This rear axle bearing puller can help to pull out semi-floating rear axle bearings quickly and effectively..
[EASY TO USE]: The washer of the axle bearing puller can captures the bearing firmly to distribute the force to the whole bearing, can avoid damage of the bearings and case..
[DURABLE MATERIAL]: The rear axle bearing removal tool is constructed from heavy duty cast steel, which has good strength and durability, can provide long service life..
[SIZE]: The bearing puller remover set includes fittings for main bearing tube: Small: 1" to 1-7/8.

Check Stock

Orion Motor Tech 3\ 4\ 6\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels (GD)

Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
Better Together: This professional or home tool kit includes three puller sizes to cover most applications: a 3 inch gear puller with a 2.3" reach and 3" max. spread.
a 4 inch gear puller with a 3" reach and 4" max. spread.
and a 6 inch gear puller with a 4.7" reach and 6" max. spread..
Versatile Reversible Design: Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside as needed..
45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that these gear pullers are backed by Orion Motor Tech's warranty and friendly customer service..

Check Stock

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
These tools make the job simple and prevent damage to your bearings when pulling.
Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
For removal only, not intended for installation.
FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
Sizes permanently laser-etched on tool for easy identification.
Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.

Check Stock

Inner Camshaft Needle Bearing Installer Tool & Remover Removal Puller Fit For 2017-2022 Harley Davidson Milwaukee Eight Engine (M8)

...Ultra Limited Low, 2017+ Harley Ultra Limited, 2017+ Harley Tri Glide, 2017+ Harley Street Glide, 2017+ Harley Softail, 2017+ Harley Road King, 2017+ Harley Road Glide, 2017+ Harley Freewheeler, 2018+ Harley Fat Boy, 2018+ Harley Fat Bob, 2017+ Harley Electra Glide, 2017+ Harley Breakout..
APPLICATION: This camshaft bearing installer tool & remove puller fit for Harley Milwaukee Eight Engines (M8) models. Compatible with all Harley Davidson twin cam..
FUNCTION: The bearing puller is designed to grip the needle bearings and prevent them from falling into the crankcase. The installation tools are designed to press on the outermost diameter of the bearing, eliminating damage to the bearing, cam, or housing. The pressure adapter also sets the bearing to the proper depth..
FEATURES: The inner camshaft needle bearing installer tool & remover puller with special style collet and fine thread. Easy to install, the design holes can be suitable for the engine, and the installation progress can be checked..
MATERIAL: Made of heavy-duty steel with black powder-coated finished, prevent corrosion and rust, solid and durable. The kit includes 12 pieces, including a cam bearing plate, installer tools, puller tools, and thumb screws, as the picture shows..

Check Stock

DURATECH 4-Piece 3-Jaw Gear Puller, 3', 4', 6', 8', Removal Tool for Gears, Pulleys, Bearings and Flywheels, Fully Assembled, CRV

Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 4 or 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas. Achieve more with its adjustable and reversible jaws..
Use the DURATECH 3, 4, 6, and 8-Inch Gear Puller 3 Jaw Flywheel Puller Set to remove most shift-fitted parts with ease. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaf....

Check Stock

DURATECH 8-Inch 3-Jaw Gear Puller, Removal Tool for Gears, Pulleys, Bearings and Flywheels, Fully Assembled, CR-V Steel

Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas..
Jaw Spread: 8in, Jaw Reach: 9-1/16in, Puller: 12T. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free replacement insures your DURATECH Wrenches purchase against manufacturer defects..

Check Stock

DURATECH 6-Inch 3-Jaw Gear Puller, Removal Tool for Gears, Pulleys, Bearings and Flywheels, Fully Assembled, CR-V Steel

Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas..
Jaw Spread: 6in, Jaw Reach: 2-9/16in, Puller: 5.7T. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free replacement insures your DURATECH Wrenches purchase against manufacturer defects..

Check Stock