ReviewsTemperature Sensing Thermistor

Sikawai W10383615 Refrigerator Thermistor with Clip Compatible with Whirlpool Refrigerator Replaces WPW10383615VP 2118226 AP6020675-2 Pack

✔️【Product Info.】- Refrigerator Thermistor W10383615 is also known as a temperature sensor, senses the temperature inside the refrigerator and....
✔️【Suitable Brands】- Compatible with Whirlpool, May-tag, Amana, Kitchen-Aid and more Refrigerator.
✔️【Replaces No.】- The W10383615 Refrigerator Thermistor Replaces AP6020675, W10383615, WPW10383615, WPW10383615VP, 2118226, PS11753994,....
✔️【Repair Symptoms 】- Frost buildup, fridge section is too warm, fridge section is too cold, the freezer section is too warm, the freezer....
✔️【100% Money-Back Guarantee】- For any reason, you are not satisfied, you can request a replacement or a full refund. Sikawai strives to....

Check Stock

Ewigkeit MK8 Hotend Ender 3 and Pro Assembled Extruder with Aluminum Heating Block 0.4mm Nozzle(24V 40W)

Ender 3 hot end with 100% original and high quality accessories for Creality 3D printer.
Ender3 pro Work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm.
MK8 Extruder Hot End Kit, white wire is temperature thermistor, red wire is heater cartridge is 24V 40W.
Tip of MK8 0.4mm nozzle, aluminum heating block, throat pipe (built-in Teflon) for 1.75mm filament.

Check Stock

W10383615 Refrigerator Thermistor With Clip Fits for Whirlpool Refrigerator Replaces WPW10383615VP 2118226 PS11753994 AP6020675 （2 Pack）

Fixes problems: Fixes problems with frost in fridges, such as parts of the fridge being too hot or too cold.
parts of the fridge being too hot or too....
Replacement: WPW10383615 refrigerator thermistor can directly replace AP6020675, W10383615, WPW10383615, WPW10383615VP, 2118226, PS11753994,....
Compatible Brands: Thermistors are compatible with Whirlpool, May-tag, Amana, Kitchen-Aid, etc..
Function: The refrigerator thermistor is also called a temperature sensor, it can sense the temperature inside the refrigerator and transmit the....
Note: Please understand this product carefully before purchasing, whether it is in line with your product model, to avoid purchasing mistakes..

Check Stock

8577274 Dryer Thermistor compatible with Whirlpool Kenmore Dryer - Replace 3976615 AP3919451 WP8577274 PS993287 by Seentech (1PCS)

✅ MODEL NUMBER: 8577274 Dryer Thermistor.
✅ BRAND NAME COMPATIBILITY: It’s a direct fit for several Whirlpool, Kenmore, KitchenAid: REPLACEMENT PART No: WP8577274, AP6013514, 8577274, 3390292, 3406294, 3976615, 772546, ER8577274, PS11746740, and WP8577274VP..
✅ HIGH QUALITY RELIABLE : The fuse is made of high quality material and tested. Forget the repairman. It only takes 20 to 30 minutes to remove a faulty thermistor and install this new one. Helpful tools include a 1/4-inch nut driver, a small flathead screwdriver, and a 1/4-inch socket and ratchet..
✅ SAVE TIME SAVE MONEY: Inexpensive way to fix or repair a dryer. Replacing the thermistor, which regulates temperature in your dryer, can fix dryers that don’t produce enough heat, don’t start, or shut off too soon..
✅ MONEY-BACK GUARANTEE: For any reason you're not completely satisfied, you can ask for a replacement or full refund, no questions asked..

Check Stock

WP8577274 Thermistor Control for Whirlpool Maytag Kenmore Crosley Dryer. Dryer thermistor temperature sensor replace WP8577274, 772546, 3390292, 3406294, 3976615, 8577274, WP8577274VP

❤[Feature] Dryer Thermistor WP8577274 attaches on the blower housing, monitors and helps regulate the temperature inside the dryer. Also called Dryer Thermistor Temperature Sensor..
❤[Compatible Brands] Compatible with: Whirlpool, Maytag, Kenmore, Crosley, Kitchen Aid, Amana, Inglis, etc..
❤[Part #] Replace Part Numbers: 8577274, WP8577274, WP8577274VP, 772546, 3390292, 3406294, 3976615, 1181075, AP6013514, PS11746740, EAP11746740, etc..
❤[Easy Installation] Easy to install within a few minutes. Easy DIY at a reasonable price, save time and money at the same time..
❤[High Quality] Well-designed, excellent process, rigorously tested, ultra durable and longevous..

Check Stock

3PCS HT-NTC100K Thermistor Sensor for Creality Ender 3 v2 Upgrade 3x15mm 3950 Compatible with E 3D V6 Volcano PT100 Ender-3-5 Pro CR10 3D Printer

【Ender 3 Thermistor, Upgrade HT-NTC100K Thermistor】Cartridge temperature sensor. Metal head diameter: 3mm, head length: 15mm,cable wire length: 1 meter,connector: XH2.54 2PIN, （Suitable for heating blocks with holes of 3mm*15mm-3mm*20mm）.
【Widly Compatibility】Product recommended operating temperature -50 °C ~ +280 °C, can replace the cartridge K-type thermocouple temperature sensor. Suitable to print multi kinds of filament.Compatible with the heatblocks with 3mm hole,such as: V6 Volcano PT100 type heated block,CR10 plated copper high temperature heating block,etc.
【High Stability and Accuracy 】Encapsulated in copper case,copper material has better thermal conductivity than stainless steel and improves accuracy.Secured with high temperature adhesive,high stability, no falling off.The internal temperature package to ensure the maximum service life with precision temperature measurement..
【Long Service Life】Compared with other products of the same type that are insulated with ordinary heat shrinkable tubes, this product uses glass fiber with a temperature resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temperature work. Thereby increasing the service life..

Check Stock

Official Upgrade Assembled Extruder Hotend with Capricorn Bowden PTFE Tubing with Silicone Cover×3 and 0.4mm Nozzle×3 for Creality Ender 3 V2 Ender 3 Ender 3 pro 3D Printer Not for Ender 5

100% Creality Original - Recently Creality has 2 kinds of heating block. Golden and Silver ones both are 100% Creality Original. The silver ones work....
Capricorn PTFE tubing - About 14 inch long. Due to its high lubricity and high-temperature resistance, it improves the printing quality and accuracy..
Pluggable: the heating tube and temperature thermistor that from control box, connect them with terminal housing and pin. Then you could plug the....
With more terminal housing and pins as spare parts, in case fail installation and waste ..
MK8 Extruder Hot End kit, white wire was temperature thermistor, braided wire was heating tube 24V40W..

Check Stock

5-PCS Ender 3 Thermistor HT-NTC100K 3D Printer ntc 3950 100K Thermistor Sensor for Creality Ender 3 v2 Thermistor Upgrade Compatible with E3D V6 Volcano PT100 Ender-3-5 Pro CR10 hotend,

（Ender 3 Thermistor, Upgrade HT-NTC100K Thermistor (1 meter each)）：Cartridge temperature sensor. Metal head diameter: 3mm, head length: 15mm,cable wire length: 1 meter,connector: XH2.54 2PIN, （Suitable for heating blocks with holes of 3mm*15mm-3mm*20mm）.
Compatibility：Product recommended operating temperature -50 °C ~ +280 °C, can replace the cartridge K-type thermocouple temperature sensor. Suitable to print multi kinds of filament.Compatible with the heatblocks with 3mm hole,such as: V6 Volcano PT100 type heated block,CR10 plated copper high temperature heating block,etc.
Stability and Accuracy：Encapsulated in copper case,copper material has better thermal conductivity than stainless steel and improves accuracy.Secured with high temperature adhesive,high stability, no falling off.The internal temperature package to ensure the maximum service life with precision temperature measurement..
Long Service Life：Compared with other products of the same type that are insulated with ordinary heat shrinkable tubes, this product uses glass fiber with a temperature resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temperature work. Thereby increasing the service life..

Check Stock

AITRIP 10PCS 3D Printer Removable 3950 NTC 100K Thermistor Sensor Compatible with Creality Ender 3 5 CR10 CR-10 CR10 Anet A8 Prusa i3 MK8

Temperature sensor 100KΩ accuracy of ± 1%, Total length:1 Meter.
Compatible with Creality CR-10S Pro,CR-X,Ender 3, Ender 3X, Ender-3 Pro, Prusa I3, Anet E10 etc.
AITRIP Thermistor Sensor is Removable design and Easy to install.
Package include: 10 thermistors. Threre is no HX2.54 connector at the end of the thermistor..
Use for heated bed or extruder of 3D Printer, with DuPont connectors..

Check Stock

Creality Upgrade Ender 3 Hotend, Assembled Extruder with Capricorn Bowden PTFE Tubing for Creality Ender 3 Pro/Ender 3 V2 with Silicone Cover×3, 0.4mm Ender 3 Nozzle×3 and 2 Pair Pneumatic Couplers

It's 100% Creality Original Upgrade Assembled Extruder Hotend..
Original Capricorn XS Serious Bowden PTFE tubing with lowest friction on the market. Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as some woodfills or ironfills..
Pluggable: the heating tube and temperature thermistor that from control box, connect them with terminal housing and pin. Then you could plug the hotend kit, easier to replace hotend kit..
With more terminal housing and pins as spare parts, in case fail installation and waste..
MK8 Extruder Hot End kit, white wire was temperature thermistor, braided wire was heating tube 24V40W..

Check Stock

Upgrade M3 Hex Screw in Fixing Thermistor 100K 3950 Temperature Sensor for Ender 3 V2 Pro CR10 and Other 3D Printer Extruder Hotend 100K 3950

M3 screw for installation is Quik and Durable, Flexible and Long Lasting, longer life span.
DIY players can also modify BLOCK by themselves. Make an M3 threaded hole in BLCOK, then you can use this thermistor.
Thermistor model: NTC 100K 3950. HERE is the firmware setting: *13:100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " &"Hotend "All In ONE"....
For the printer which uses NTC 100K 3950 thermistor, Then this thermistor is plug and use.

Check Stock