ReviewsTest Terminal Blocks

Electronics-Salon Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA-2560 R3.

Prototype Screw/Terminal Block Shield Board Kit For Arduino MEGA-2560 R3..
FR-4 fiber glass PCB, dual copper layers, size 120mm x 78mm..
Pads grid / pitch 2.54mm / 0.1", hole diameter 0.8mm. Terminal block pitch 3.5mm / 0.138", hole diameter 1.2mm..
Pitch 3.5mm / 0.138" mini terminal blocks, total 84 pins(3pole x24pcs, 2pole x6pcs )..

...lly and give you a buzzer prompt, reminding you whether the tested component is faulty..
[ How to Use ]: Clip the red clip to the positive electrode of the car battery and the black clip to the negative electrode of the car battery, press button to “Positive”side with LED lighting RED, conact the tip to positive terminal of tested component to active the component. If LED turns to GREEN with buzzer, stop testing and check the component if defective or not, or rating current of component is higher than that of this tester..
[ Packing Include ]: 1 X Power Scan, 1 x Probe Tip, 1 x Battery Hookup Clips, 1 x User Manual, 2 x clips. The cable length of the circuit tester is about 4m(13ft) which allows you access and test any electrical system easily. Note: This circuit tester can not be used for 110/220V systems, it is only used for DC 6-24V systems. Do not use on AC voltage..
[ NOTE ]: Before performing the test, please make sure that your tester is properly connected. Connect the red clip to the positive terminal of the car battery. Then connect the black clip to the negative terminal of the car battery. During the continuity test, the auxiliary ground wire needs to be connected to one side of the wire under test. When testing components in/out of the v....

Max. amperage: 80A, max. voltage: 32V DC, #10 mounting screws, screw terminal torque: 25 in-lb, wire size: 14-4 AWG.
Snap-on terminal cover insulates all conductive parts, satisfying ABYC/USCG requirements.
Cover breakouts allow wires from sides or bottom. Label recess accepts large format label.
Terminal screws compress fuse blades within blocks for low resistance connections.
Accepts MAXI Fuses. Fuse sold separately.

...red, the outlet will not have any power, making it more safe than conventional receptacles..
TEST FUNCTION. The receptacle will not reset normally if the GFCI circuit is not functioning properly. If GFCI has been wired properly, you can press the RESET button fully and it will supply the power to outlet and the load terminal.
Press the TEST button to test the GFCI and will stop the flow of electricity. This GFCI Outlet has LED Indicator lights to let you know the power, connection and protection status of the receptacle..
EASY INSTALLATION. Mounting screws are shipped captive in the device and wall plate for easier installation. It replaces an existing outlet only spend as short as 10 minutes. Wall plate and Complete installation instructions included..

Support AC and DC control signal, Relay action LED indicator, relay coil protection by means of a freewheeling diode..
Panasonic PA1a SPST-NO 5Amp power relay. Original Panasonic PA1a-PS pluggable socket for support replacement relay, and with removal key..
Dinkle high quality fireproof nylon material DIN rail mount housing, can support width 35mm, 32mm and 15mm rail..
High quality screw terminal blocks and clear marking label for terminal block position. Pitch 5.08mm/0.2" and 7.62mm/0.3" screw terminal block. Wire range 26 to 12AWG / 2.5mm square. Screws - M2.5, steel, Cr3+ Zn plated. Pin header and Cage - Brass..
High quality glass fiber FR-4 PCB, top and bottom dual copper layers..

【Product Name】 6 Pin, Plug-In 5.08mm/0.2" PCB Terminal Block.
【Rated Voltage】300V, Rated Current：10A.
【Easy to Use】No soldering required. Just use a small screwdriver to open up the terminal blocks, slide in your stranded or solid-core wire, and re-tighten. Save you from solder trouble, no need to purchase expensive tool. Great time and money saver..
【Application】: PCB terminal is widely used in electronic equipment, such as small electronic watches, calculates, general computer, communication electronics equipment automatic control system, domestic appliance and warning devices, etc..

- 100% brand new and high quality binding posts, made of premuim alloy material which can provide good electrical conductivity and insulated with ABS plastic..
- These binding posts allow the connection of several different types of connections such as banana plugs or pin connectors..
- Binding Post Connector are also great connectors on loudspeakers and audio amplifiers as well as other electrical equipment..
- Binding Post Terminal is widly used on electronic test equipment to terminate (attach) a single wire or test lead..
- Total 5 colors that you can use for color-coding to meet you different demands: red commonly means an active or positive terminal.
black indicates an inactive or negative terminal, etc..

The EZSync912 HDMI to terminal block adapter connects all 20 signals(including shielding) from a HDMI connector to two 10-position terminal block connector. The two 10-pin terminal blocks support screw-type wiring with enclosure and cable strain relief suitable for heavy duty industrial wiring applications..
Plastic case. Solderless terminal block. Compatible with HDMI 2.0, 1.4 and 1.3. Distance will be depending on cable quality..
Each package contains 2x sets of adapter kit. Size: Body-50mm x 23mm x 18mm.
Wiring diagram provided in image is for typical installation. The actual wiring could be different depending on your equipment..
If you don't know the wiring order on the other end of the cable, you need to ohm it out if you have a meter or cut the other end and re-wire both ends.

Made of high-quality carbon steel, nickel-plated surface, durable..
Phillips pan head screws have deep threads and do not slip..
The combination of the terminal block screw and square washer makes it easy to fix wires in electrical facilities..
It is suitable for the crimping of electrical appliances such as switches and terminal blocks..

Made of high-quality carbon steel, nickel-plated surface, durable..
Phillips pan head screws have deep threads and do not slip..
The combination of the terminal block screw and square washer makes it easy to fix wires in electrical facilities..
It is suitable for the crimping of electrical appliances such as switches and terminal blocks..