ReviewsThrust Bearing Auto Bearing

SKF F4B 104-RM Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Contact Seal, Cast Iron, 1-1/4\ Bore, 3-5/8\ Bolt Hole Spacing, 5730lbf Dynamic Load Capacity

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Specs: Swing Arm Bearing Kit, Needle Bearings 52100 bearing steel ARC6.
POM composite washer bearings replace thrust needle washers for superior resistance twater and dirt and increased service life.
Compatible With/Replacement For: Suzuki LT-250R 1985 - 1992, LT-500R 1987 - 1990.
100% New aftermarket Swing Arm Bearing Kit built to meet OEM specifications.

Double honed bearing surfaces provide absolute reliability at high RPM.
Increased wrist pin lubrication with double drilled small end.
Specially designed side scalloping vent slots on large end to maximize rod bearing lubrication.
Includes connecting rod, crank pin, crank pin bearing, thrust washers, and wrist pin bearing for two strokes.

Price For: Each Overall Width - Roof Ventilators: 12-3/4" Overall Width (In.): 12-3/4 CFM @ 4 MPH Wind: 147 Requires: Base for New Installations, Flashing Item: Turbine Ventilator Item - Roof Ventilators: Turbine Ventilator Construction Material: Galvanized steel With Aluminum Bracing Includes: - Type: Wind Driven.
Bearing System: Features Oiless Bronze Upper Bearing and Lower Thrust Type ball bearing Overall Height - Roof Ventilators: 14-1/2" Throat Dia.: 6" Overall Height (In.): 14-1/2 Bracing - Roof Ventilators: External Bracing: External Country of Origin (subject to change): United States.

Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
Manufactured to meet or exceed OE specifications.

Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
Manufactured to meet or exceed OE specifications.

Precision Medium Duty Live Center For General Purpose On Manual Engine Lathe.
The live center has a combination of deep groove ball bearing, thrust ball bearing and needle bearing..
The anti-dust seal can prevent cutting fluid and dust from entering into the center bearing.
The 60° rotating spindle is made from carbon alloy steel with heat treatment to HRC 58±2 for high rigidity and wears resistance.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.