ReviewsTool And Die

Greenfield Threading 423107 Collet, 5 1/4\

  • Die construction: two-piece die assembly.
Check Stock

Greenfield Threading 423109 Collet, 5 5/16\

  • Die construction: two-piece die assembly.
Check Stock

Greenfield Threading 423128 Guide, A1#4, Carbon Steel, Uncoated (Bright) Coating, 2-Piece

  • Die construction: two-piece die assembly.
Check Stock

Greenfield Threading 423111 Collet, 5 3/8\

  • Die construction: two-piece die assembly.
Check Stock

YON.SOU. Air Die Grinder - 1/4\

  • ... grinder could prevent accidental engagement, you wouldn't get hurt even if you just start to learn to use the air die grinder. The air inlet filter could keep the die grinder from contamination. Built-in regulator makes it easy to control air die grinder's speed..
  • ⚙️ VARIOUS APPLICATIONS: This angle die grinder tool is air-powered, you should connect the air grinder to an air compressor before use. With variable speed and changable bits or pads, the die grinder is suitable for various applications, such as machining, smoothing, chamfering, deburring, grinding, polishing, engraving for metal, woodwork, tire, plastic, etc..
Check Stock

ABN Power Punch Heavy Duty Hole Punch Set – Metal Hole Punch, Heavy Duty Hole Puncher Hand Punch 3/32in to 9/32in

  • PUNCH HOLES IN YOUR PROJECT: The ABN Hole Punch Tool is a heavy duty punch and dies kit that has a high-leverage design and comfortable grips that allow you to manually create clean holes through sheet metals up to US 16 gauge.
  • For mild sheet steel, aluminum, brass, polyurethane, plastic, canvas, cardboard, paper, shoe.
  • Additionally use as a leather punch, belt hole puncher, metal hole punch for jewelry, and watch hole puncher.
  • Not recommended for stainless steel such as silverware and utensils.
  • PERFECT SIZE: Creates holes that are from 3/32-inch to 9/32-inch in diameter and includes a stop gauge for consistent spacing.
  • 7 sizes of punches and dies include 3/32-inch (2mm), 1/8-inch (3mm), 5/32-inch (4mm), 3/16-inch (4.5mm), 7/32-inch (5.5mm), 1/4-inch (6mm), 9/32-inch (7mm).
  • 1.75-inch (4.4cm) throat depth to punch holes as close as 1.75 inches away from material edge.
  • EASY TO USE: This sheet metal punch uses interchangeable heads to pierce holes in a material of your choosing.
  • Select a proper size punch and die, remove nut near handle using die adjustment tool, move connection bar, place punch on the head of hand punch, rotate nut by again using the adjustment tool to adjust caliper, and set distance between the edge and the hole.
Check Stock

SOLEILLUNE Battery Cable Lug Crimping Tool for AWG 10, 8, 6, 4, 2, 1 Terminals with 60Pcs 8Specs Copper Ring Cable Lugs Kit Heavy Duty Wire Terminal Crimper for Electrical Connectors

  • 【LIGHTWEIGHT MATERIAL】The handle of the Wire Crimper tool is made of high-quality 6061-T6 aluminum alloy, with a lighter weight of only 2.35 pounds, which makes the crimping tool more convenient to carry and use. The head of the wire crimping tool is made of high-quality carbon steel with longer service life. The long handle of the battery terminal crimper wrapped with non-slip soft vinyl help you use less effort when crimping..
  • 【ROTATE CRIMP DIES】The professional cable terminal crimping tools are available in 6 crimping sizes, 10, 8, 6, 4, 2, 1 AWG (Corresponding to 6mm²/10mm²/16mm²/25mm²/35mm²/50mm²), and use a hexagonal rotating crimp die which is retained in place with a spring loaded locking pin. Thanks to processed by Wire EDM Cutting, the crimp die is more accurate than the ordinary casting die or stamped die..
  • 【EASY OPERATION】Open the handle of the crimper, then press the Lockpin and rotate the crimp jaw to the size you need, place the cable and lug, then pull strongly on the ratcheting wire terminal crimper to make a great crimp on the cable lugs. Finally, rotate the connector 90 degrees to another direction and repeat the previous step for secondary crimping. Crimping twice is more secure..
Check Stock

Pocket Level 4\ x 1.8\ Mini Spirit Level 3 Vials Magnetic Base

  • The item is Swanson Tool TL002M Magnetic Die Cast Torpedo Level.
Check Stock

Swanson Tool Co TL002M 9-Inch Magnetic Die Cast Torpedo Level

  • The item is Swanson Tool TL002M Magnetic Die Cast Torpedo Level.
Check Stock

Snaps Rivet Grommet Prong Eyelet Popper Fastener Self Cover Fabric Button Hand Press Machine Set

  • [Handpress Machine] Universal Hand Press Machine for grommets, snap buttons, rivets, fabric covered buttons.
  • [Snap Button Dies] 1 set of die for 10 mm 'S' spring press fasteners type VT2 (includes 4 pieces) 1 set of die for 12,5 mm 'S' spring press fasteners type T54 (includes 4 pieces) 1 set of die for 15 mm 'S' spring press fasteners type Alfa (includes 4 pieces) 1 set of 9.5mm Perforated prong snap button fastener button tool/die (includes 2 pieces).
  • [Rivet Dies] 1 set of 7mm Rivet Die/Mold (includes 2 pieces) 1 set of 9mm Rivet Die/Mold (includes 2 pieces).
  • [Grommet Eyelets Dies] 1 set of 5.4mm Grommet/Eyelet Die/Mold (includes 2 pieces) 1 set of 7.5mm Grommet/Eyelet Die/Mold (includes 2 pieces) 1 set of 9mm Inner Diameter Grommet/Eyelet Die/Mold (includes 2 pieces).
  • [Hole Puncher] 1 piece 2mm Hole Puncher 1 piece 4mm Hole Puncher 1 piece brass base for a hole cutter.
Check Stock

Muzerdo 131PCS Sae and Metric Coated Bearing Steel Tap and Die Rethreading Kit

  • Muzerdo tap and die set is one of those toolboxes that are not immediately intuitive to have but become essential to your work once you have it. It does not matter if you are a mechanic, a craftsman, a metal or woodworker, or even a DIY enthusiast, a tap and die set would be remarkably useful to you. Taps and dies are cutting tools used to create threads on components such as screws, bolts, nuts and to create a threaded hole to screw components into..
  • A tap is a threaded tool that cuts or forms threads in the female portion of a mating pair. Therefore, a tap will create threads in the inside of a hole. On the other hand, a die is a threaded tool that cuts or forms threads in the male portion of a mating pair. Therefore, a die will create threads on a cylindrical rod's surface to create a screw or bolt. Both a tap and a die create new threads or repair damaged threads..
  • Our tap and die set consists of taps, dies, and drill bits of different sizes for various applications. Included in the set are handles for turning. The collection also consists of screw extractors and charts to determine the correct drill and taps to match the thread size and pitch. Some sets may contain twist-lock guides, coarse and fine taps, and other tools at a higher cost..
Check Stock