ReviewsTube Fitting Forged Elbow

Anderson Metals 50065 Brass Compression Tube Fitting 90 Degree Elbow 3/8 x 3/8 Tube OD,50065-06

  • 90-degree elbow for connecting two tubes at an angle.
  • Female compression tube fitting for connecting to male threaded pipes.
  • Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
  • Operating temperature range of -65 to 250 degrees F.
  • These fittings contain lead and are not allowed by federal law to be installed for potable water use in the U.S.A. and its territories..
Check Stock

(30) 1/2\ Brass PEX Fittings 10 Each Elbow TEE Coupler Reducer Lead Free Crimp Cinch PEX GUY

  • Manufactured to ASTM Standard F1807 and CSA B137.5 for use with any SDR-9 PEX tube. COMPATIBLE with ONLY Crimp or Cinch Type rings and/or connectors. NOT Compatible with: -Expander Fitting System, Uponor/Wirsbo Expander System.
  • Lead free brass. Great for any potable water and radiant heating application..
Check Stock

Pysrych 304 Stainless Steel Compression Tube Fitting 90 Degree Elbow 1/4 OD x 1/4 OD Pack of 2

  • 90-degree elbow for connecting tubing to threaded pipe at an angle..
  • Twin ferrule compression fitting for a leak-resistant seal in high-pressure applications..
  • 304 stainless steel for higher strength and greater corrosion resistance,good sealing and repeatability, convenient installation and maintenance, safe and reliable operation..
  • Temperature Range: -50-450℃ / -58℉ -842℉..
Check Stock

Vis Brass CA360 Flared Tube Fitting, SAE 45 Degree Flare, Cap, 3/8\ Tube OD (Pack of 5)

  • Cap fitting for closing the end of a male-threaded flare tube.
  • Forged nuts for refrigeration applications.
  • CA360 brass for strength and resistance to corrosion.
  • Operating temperature range of -65 to +250 degrees F (-53 to +121 degrees C).
Check Stock

2Packs CPAP Headgear for Respironics Dreamwear Full Face Mask, Headgear for Respironics Dreamwear Full Face Mask or Dreamwear Gel, Clips NOT Included

  • Quick Release: The elbow is quick release, quick release is easy and fast. It is stuck between the clear elbow and the part that inserts into the CPAP's hose, if you got up and tugged in an emergency. You could pull it out of the hose without damaging the end of the hose and it is easy to achieve a tight connection. WARM TIPS: There is a white piece in the heating tube, you need to remove the clear piece of the elbow before use, otherwise the elbow would not fit into the heated CPAP tube..
  • Convenient & Flexible for Using: It's very well made and light, it has an elbow shape and directs the hose to where it needs to be in order for it to stay out of the way..
  • Prevent The Hose From Tangling: The original hose that was supplied with the machine didn'tprovide much ability to move around. The elbow allows the hose to rotate if you roll around during the night.Keep the hose from tangling up..
  • Easy To Install: The swivel is easy to install, easy to connect, and provids very nice 360 degree "spin" for the hose. Swivels and seals correctly, helps pivot the tube keeping it more comfortable when sleeping..
  • Vent Holes: The vent holes could promote the emission of carbon dioxide and prevent the carbon dioxide from being inhaled into the body again, so the vent h....
Check Stock

SHURFLO (244-3926 Elbow Adapter

  • Wingnut Swivel, Nylon: Pump head fittings included with each pump.
  • 1/2 inch x 14 Male Pipe Thread (F) x 1/2 inch Barb, Elbow Fitting.
Check Stock

DOT Brass Air Line Quick Connect Fittings Assortment, 34 Pcs DOT Push to Connect Air fittings 1/4" 3/8" 1/2" Air Fitting Kit with 1/4" Schrader Valve Air Line Fittings for Trucks or Industrial

  • 【PREMIUM MATERIAL】：Our dot push to connect air fittings are made of high quality CA360 brass, meet D.O.T. FMVSS 571.106, SAE J1131 with corrosion resistance, high temperature ductility and low permeability. Long service time, air brake fitting assortment type: 1/4", 3/8", 1/2"..
  • 【TYPICAL APPLICATION】：The dot air line quick connect fittings can be used with air suspension systems, copper tubing in air lines brake systems, perfect for truck /RV repair air line leak, also perfect for industrial workshops, daily garden or lawn mower repair, towing machine hose connection and so on..
  • 【EASY TO INSTALL】：Pre applied red sealant for male thread for better sealing. All brass quick connect air fittings can be sealed by pushing the tube firmly into the fittings, simply depress button to remove tubing..
  • 【MAX PRESSURE】：Working pressure from vacuum to 250 psi. Temperature Range: -40° F to +200° F（-40°C to +93°C）(Note: see tubing manufacturer's recommendations for pressure and temperature mutations).
  • 【ALL IN ONE SET】: Unique DOT Air Brake fit....
Check Stock

Builder's Best 010155 Venting. Offset Elbow, Dryer, 4-1/2 In, 1 Cubic Centimeters

  • ☑PART NUMBER: Cenipar Dryer Vent Hose- Flexible Aluminum Foil Ducting Vent Hose(4 inch 8 feet) with 1 X 8 in Flexible Aluminum Foil Ducting Vent Hose&2 X metal Clamps. Cenipar STV-90 Drying Tube Fitting, DIY Simple Dryer Ventilation Connection Kit with 1* 90 elbow, 1* drying hose clamp, 1* plastic drying hose..
  • ☑ WHAT IT IS: Dryer Vent Hose 4" Duct Vent Hose is a flexible vent hose made of high quality flame retardant aluminum that measures 4" (diameter) x 8 feet (length) when fully unfolded. The silicone seal in the STV-90 gives you a sealed dryer connection, making your dryer more efficient while consuming less energy and saving on electricity bills. With our newest STV-90 dryer duct connector design, you can install any 4" vent pipe or 4" flexible dryer hose, curved or straight to match..
  • ☑EASY INSTALLATION: Step 1: Tightly combine the drying hose clamp with the Dryer Vent Hoseto prevent the drying hose clamp from falling off the dryer vent hose.Step 2: Combine the protruding part of the dryer vent elbow with what you just finished in step 1, so that they keep a tight connection.Step 3: Insert the sealing ring into the other interface of the dryer exhaust elbow and finally connect it with the dryer vent.You can also find repair videos on YouTu....
Check Stock

GASHER 26PCS Brass Pipe Fitting Kit, Hex Bushing, Reducer Adapter, Hex Nipple, 90 Degree Barstock Street Elbow

  • 【DURABLE】Not a cast product, more robust and durable than castings. Max. pressure 150 PSI..
  • 【MATERIAL】 Durable solid brass construction is resistant to corrosion and long-lasting..
  • 【THREADS】 Male and Female National Pipe Taper (NPT) threads for connecting two pipes.
  • 【TEMPERATURE RANGE】 Operating temperature range of -65 to +250 degrees F..
  • 【INCLUDE】1 x 1/4 Tee Fitting, 4 x1/4 Elbow Fitting, 4 x 1/8 Elbow Fitting, 1 x1/4 Coupling, 1 x 3/8-1/4 Nipple & Reducer & Bushing, 1 x 1/4-1/8 Nipple & Reducer & Bushing.
Check Stock

1/2\ Floor Flange, Home TZH Malleable iron Pipe Fittings for Industrial vintage style, Flanges with Threaded Hole for DIY Project /Furniture/ Shelving Decoration (10 Pack)

  • 3/4 INCH PIPE ELBOW – TEN PACK: Our Brooklyn Pipe cast iron fittings 10 pack elbow pipes are made with from superior steel with 100% durability and strength and provides you with great flange elbow fittings at a very affordable price..
  • PERFECT FOR DIY: Whether you’re looking to build a pipe shelf, pipe towel rack, pipe lamp, our malleable 90 degree elbow industrial fitting is up to the task. These fittings are for decor and DIY projects only, they are not rated to carry gas or water..
  • RAW IRON: Our 3/4 inch black malleable iron pipe fittings are raw and unfinished iron. This means that you will need to seal or paint the flanges for your project. When handling raw iron, it’s normal for your hands to get dirty. You’ve probably seen iron workers in movies, they don’t come home clean!.
  • ONE CONVENIENT PACK: Our 3/4 90 degree elbow threaded flanges fittings pipes give you 100% super convenient benefits than other bands because our Brooklyn Pipe elbow is designed to be compatible with your all project parts.
  • UNLEASH YOUR CREATIVITY: We inspect and pack each pipe fitting and we offer a LIFETIME warranty on our products, just give us a call or send an e-mail. Now, with our black pipes bring the rustic, industrial style into your home, office or any inte....
Check Stock

Midwest Industrial Tanks Waste Oil Tank - 500-Gallon, Model Number RTD-W-CC-500-10-12

  • Equipped with emergency vents, level and leak gauges, a 2in. suction tube with cam lock fitting, and locking fill box with integrated filter drain.
  • Ports provided on both inner and outer tanks for easy access.
  • Heavy-duty forged steel port flanges allow for use with all necessary vents, fill ports and pumping equipment.
  • Protective powder-coat finish looks great and extends durability.
Check Stock