ReviewsTwo way Thrust Bearing

DNJ TW950 Thrust Washer For 88-04 Toyota, Lexus, Tacoma, Tundra, 4Runner, T100, Pickup, ES300, Camry, ES250, 2.5L-3.4L V6, DOHC, SOHC, Naturally Aspirated

Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
Manufactured to meet or exceed OE specifications.

Single-row angular contact ball bearing, supporting moderate to heavy one-directional thrust loads, and combined loads where thrust load is predominant.
Ball contact angle of 40 degrees relative to the inner and outer raceways increases thrust load capacity.
Open configuration for lubrication applied in place.
Brass cage evenly spaces balls for reduced friction, vibration, and noise.
ABEC 1 tolerance ratings for accuracy and low rotational speeds.

Two-bolt housing with ball bearing insert for a ready to mount installation.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Relubricatable solid one-piece housing pillow block for maximum strength and rigidity.
Non-expansion-type bearing with setscrew locking collar for secure attachment to guided shaft.
Felt seal to protect against contaminants and retain lubrication.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Two-bolt flange-style housing for a ready-to-mount installation where surface and guided shaft are perpendicular.
Single-row deep groove ball bearing insert accommodates misalignments between the shaft and the housing.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.