ReviewsUniversal Tap Set

ABN 131-Piece Metric Thread Repair Set – Damaged Helicoil-Type Thread Master Repair Kit for Automotive Repairs

  • Screw tap and thread insert sizes M5x0.8x6.7mm, M6x1.0x8.0mm, M8x1.25x10.8mm, M10x1.5x13.5mm, M12x1.75x16.3mm (where M12 means thread outer diameter = 12mm, 1.75 means pitch of thread = 1.75mm).
  • [Quick Organization]: Steel carrying case with latch and molded plastic inside tray insert to keep universal thread repair tool pieces separated and easy to access.
  • Includes bottom recesses for organizing the coils in included plastic bags.
  • [Easy to Use]: Remove your damaged thread by using an included twist drill bit.
  • Load the thread insert into installation tool.
  • Use the breaking pin tool to remove tang from insert.
Check Stock

Mudder Bpv31 Piercing Valve 134a Kit R134a Refrigerant Charge Hose with Gauge, Hose Refrigerant Can Tap with Gauge R134a Can Connect to R12/r22 Port Ac 1/2 and Universal Retrofit Valve with Dust Cap

  • Package content: 3 packs BPV-31 piercing tap valve kits (each kit contains 1 piercing valve, 1 hex key and 2 adapters), including R134a U-charge hose with gauge and can tap, universal retrofit valve with a dust cap, 5 packs in total, bring you more convenient for replacement.
  • All our replacement kits are made of corrosion-resistant metal that won’t wear out or rust over time, with anti-leaking design that will be safer for you.
  • Easy to install: our BPV-31 piercing tap valve kits come in compact design that only requires a 2-inch clearance area for installation and use, and you only need 1 hex key wrench (included) to install the kit.
  • If you want to attach the gauge with BPV piercing tap valve, you need a retrofit valve (included).
  • R134a Charging hose: 19 inch hose with R-134a can to R-12/R-22 service port connection, 1/2 inch end fits R12, 22, 502 fittings.
  • And the gauge has scale readings for R134, R12, and 22. 90-degree push and lock coupler with auto shut off.
  • Replace model of BPV-31 piercing tap valve: AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31.
  • Compatible with 1/4 inch, 5/16 inch, 3/8 inch outside diameter pipes.
  • Universal retrofit valve: the retrofit valve converts from R-12 to R-134a air conditioning system and suit for 7/16 inch ....
Check Stock

Patioer R134A Refrigerant Charging Hose Gauge, Refrigerant Recharge Hose Kit with 3 Pack BPV-31 Bullet Piercing Tap Valve Kit for Car AC Air Conditioning Refrigerant Charging Can to R-12/R-22 Port

  • PACKAGE INCLUDES 5 PACKS: 3 x BPV-31 bullet piercing tap valve kits, each one contains 1 piercing valve, 1 hex key and 2 adapters.
  • 1x R134A U-charge hose with gauge and can tap.
  • PREMIUM MATERIAL: Made of high quality metal with great rust-resistant and anti-leaking performance. The hose is made of rubber,good pressure resistance, safe to use..
  • R134A CHARGING HOSE: 15.3inch/39cm long, with R-134a can connect R-12 / R-22 service port, 1/2" end port fits for R12, R22, R502 fittings. And the gauge has scale readings for R134, R12, and R22. 90-degree push and lock coupler can auto shut off..
  • EASY TO INSTALL: BPV-31 bullet piercing tap valve kits are equipped with hexagonal wrench of suitable size, which is more convenient to install. Use the retrofit valve to attach the gauge with bullet piercing tap valve..
  • UNIVERSAL RETROFIT VALVE:  Retrofit valve converts from R-12 to R-134a. Fit for 7/16 inch low side port.
  • Suit for vehicles pre-1994, comes with R-134a refill fittings. Replace AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31.Compatible with 1/4 inch, 5/16 inch, 3/8 inch outside diameter pipes..
Check Stock

Neiko 00916A 45 Piece SAE Tap & Die Set, SAE Tap and Die Set, Tap Set, Rethreading Kit, Pro-Grade Large Tap and Die Set, Titanium Threading Tools, Thread Chaser Set, Tap & Die Set Standard

  • HEAVY DUTY TAP & DIE SET: Titanium cutting edges hold sharpness up to 20x longer than steel, making this a perfect SAE tap and die set for any project, big or small..
  • VERSITILE: Create new threads or repair damaged threads on most metals like carbon steel, cast iron, aluminum, brass, copper, and stainless steel with this tap and die kit..
  • DURABLE STORAGE CASE: This large tap and die set standard is fully equipped in a heavy-duty molded case for easy identification, storage, and portability for all your jobs on the go..
  • PREMIUM MATERIAL: Our SAE thread chaser set is made of a professional grade steel, highly durable and built to last for multiple uses. This tap set is perfect car repairs, DIY projects, and much more..
  • COMPLETE SET INCLUDE: This rethreading kit comes with the most popular SAE taps & dies. T-handle tap wrenches, adjustable die wrench, screwdriver, and thread pitch gauge..
Check Stock

Machine Tap 1/2\-13 UNC Thread Pitch 4 Flutes, High Speed Steel Thread Forming Tap, Uncoated (Bright) Finish, Round Shank with Square End, Plug Chamfer, HSS Machine Screw Plug Tap

  • CUT & RENEW THREADS: The ABN | Metric Tap and Dies Set 110-Piece Metal Threading Kit cuts and renews external and internal threads to exact standards.
  • Ideal for professional machinists and DIY weekend warriors alike to rethread existing auto and machinery fasteners, remove screws/bolts, cut raw material.
  • Tap wrench fits the different sizes of taps, thread taps are used to process internal thread, thread die set is for external thread, plug taps suitable for cleaning and rethreading.
  • FITS YOUR APPLICATION: Metric – Taper taps (2x0.4, 3x0.5, 4x0.7, 5x0.8, 6x7.5, 6x1, 7x0.75, 7x1, 8x0.75, 8x1, 8x1.25, 9x0.75, 9x1, 9x1.25, 10x0.75, 10x1, 10x1.25, 10x1.5, 11x0.75, 11x1, 11x1.25, 11x1.5, 12x0.75, 12x1, 12x1.25, 12x1.5, 12x1.75, 14x1, 14x1.25, 14x1.5, 14x2, 16x1, 16x1.5, 16x2, 18x1.5,).
  • Tap wrenches (M3-M12 x 1/16”-1/2”, M6-M20 x 1/4”-3/4”).
  • Die wrenches (25mm x 1”, 38mm x 1-1/2” OD).
  • BUILT TO LAST: Constructed from chromium-coated high carbon steel for maximum strength and corrosion resistance.
  • Metric tap set has 3-4 flute abrasive cutting edges each so you can easily clean/repair and cut materials such as aluminum, iron, cast iron, alloy steel, carb....
Check Stock

Muzerdo 115PCS Sae and Metric Bearing Steel Tap and Die Rethreading Kit with Metal Box

  • Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more.
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of course then you don’t have t.
Check Stock

Toolly 32pcs Tap and Die Set, Metric Hardened Steel Tool Set, Essential Threading & Rethreading Tool with Storage Case Perfect for Auto and Machinery Repair

  • 【32pcs Tap and Die Set】The package includes 28pcs (each size including 1x taper tap, 1x second tap, 1x plug tap and 1x die): M3 X 0.5, M4 X 0.7, M5 X 0.8, M6 X 1.0, M8 X 1.25, M10 X 1.5, M12 X 1.75.
  • 1 x Tap Wrench, 1 x Die Stock Wrench, 1 x Thread Pitch Guage, 1 x Screwdriver, to cover all your needs..
  • 【Product Function】Tap and die set in metric is perfect for rethreading fasteners, fastener holes for auto and machinery repair. Threading tool with storage case, can greatly increase your productivity and act as an important part to your work..
  • 【Tapered Teeth Design & Versatility】Taps (for internal threads) and Dies (for external threads) feature with tapered teeth that start threading more easily. Perfect for creating new threads or repair damaged threads on most metals like carbon steel, cast iron, aluminum, brass, copper and stainless steel..
  • 【High Quality & Durable】Tap and die set adopts premium hardened steel material. The screw thread tapping tool is durable to use. The better the material the tougher the tap and die so they ensures durability and tool longevity to withstand professional uses..
  • 【SIZE LABLED】All of them are clearly labled with size for you to find quickly, and be able to pull the right size out of the box when you ....
Check Stock

Logitech Harmony Touch Universal Remote with Color Touchscreen - Black [Discontinued by Manufacturer]

  • Intuitive color touch screen: Access all your entertainment options, like Watch TV or Listen to Music , with one touch.
  • Customizable channel icons: Set up to 50 favorite channels on the touch screen, change channels with one simple tap, and organize them the way you....
  • Sleek, streamlined design: Sculpted, ergonomic shape and uncluttered back-lit button layout for easy navigation even in the dark.
  • Recharging station: Keeps your remote charged, ready and always in reach.
  • Universal control of up to 15 devices: Works with 5,000+ brands and 225,000+ devices, including ones you add tomorrow.
Check Stock

Fafeicy Stripped Screw Remover, Tap Extractor Set, High Speed Steel Steel Broken Head Taps Remover, Stripped Screw Tap Extractor Set, for Removing Screws and Bolts(six-piece set)

  • Tap Extractor Set is made of superior high speed steel, high hardness and anti-corrosion..
  • Each Tap Extractor is specifically engineered for speedy grab-it and easy out broken screw taps..
  • Tap Extractor Set works for removing stripped, rusted, broken, or corroded screws and bolts..
  • Every tap extractor goes through rigorous quality testing, durable to use..
  • Tap Extractor Set is suitable for industrial screw and bolt removal and for everyday home repair work..
Check Stock

szgate 5PCS Combination Drill Tap Bit Set Screw Tapping Hex Shank HSS MetricImperial Plug Drill Bits Hand Tools 6-32NC, 6-32NC (3.5mm)

  • The wide range of drill tap bit set helps you with tasks like drilling, tapping, deburring and countersinking, all with this single kit. The split point tip resists walking and penetrates faster into the material. Along with fast penetration, the power drill makes your life easy by saving your time and energy..
  • Durable taps are made from hardened high-speed steel (HSS ) vs carbon steel for longer life,which can drill, tap, deburr and counter holes on wood, copper, brass, aluminum, sheet metal and plastic.
  • This is a SAE drill tap set, so it has high versatility. Each tap drill is engraved with a label, which is convenient for you to choose the size that suits you. Quick Change ¼-inch (6.35mm) hex shank has a tapered end to prevent excessive knocks. Back taper exceeds the tap to prevent over-drilling and damage to the thread..
  • Can be used to tap various threads. including 6 SAE sizes: 6-32NC, 8-32NC, 10-24NC, 10-32NC, 12-24NC, ¼-20NC,1/4inch hex quick change shank fit Electric hand drill, impact drill, bench drill,electric screwdriver and other tap machine.
  • Easy to Carry and Use,As the Drill Tap Bits set comes with a portable storage case you can carry it anywhere you go. If you encounter any problems or are not satisfied with the products while usi....
Check Stock

ATOPLEE Spiral Point Plug Threading Tap ,5pcs HSS 6542 Titanium Coated Metric Right Hand Thread Taps,M3-M8

  • Tap and Die Bit Diversity – These tools are sold as a set for good reason. You really should look to get as much diversity in the sizes of the taps and dies as you can. That way you will be able to pull the right size out of the box when you need it..
  • Wrenches – All tap and die bits need to be mounted in a wrench. Broadly speaking, they are all roughly the same, with a few notable exceptions. The tap wrench from Muzerdo, is the best on the market..
  • Construction Material – Steel is the base metal used in the construction of these sets – but not all steel is created equally! Look for steel alloy or, even better, Titanium tipped cutting surfaces. The better the metal the tougher the tap and die so they so they can cut into more materials and they will stay sharper for longer..
  • Metric/SAE – The size of the tap and die is also important. Metric is of course the European measurement system, SAE are based on US sizes (so use inches instead of millimeters). This is important as you may struggle to use a SAE tap and die set on a vehicle with metric measurements. If the car is made in the US, it probably uses SAE measurements. If it is a European carmaker, it’s probably the opposite. If can look for a set with dual Metric and SAE compatibility of cour....
Check Stock