ReviewsWater Pump Bearing

KOLERFLO 3/4 Inch 110V Circulating Water Pump Hot Water Circulation Pump/Circulator Pump for Hot Water System(RS15-6 Green)

.... NPT 3/4 inch (19.05 mm) inlet/outlet. Voltage/Frequency: 110-120V, 60Hz. Max pressure: 145 psi (10 bar),the circulation pump with three-speed control. Flow: 36/29/20 LPM (9.5/7.66/5.28 GPM). Max head: 6/4.9/4 m (20/16/13 ft).
Pump housing: Aluminum. Impeller: Corrosion-resistant, composite, PES. Shaft: 45 # steel. Bearing: Carbon axia..
Easy installation, only need a wrench to connect the pump to the pipeline, saving you the cost of plumbers.
Instant hot water, waiting for 2-3 minutes in the past, now it takes only 15 seconds to get hot water..
Prevent pipes from freezing in winter, especially for cold winter areas. In addition, if your pipes pass through the floor, the floor will also become warm..
The circulation water pump features high efficiency with low consumption. High temperature resistance, anti-fraying, high flow and leak-tightness. Super silent, environmental friendly,saving energy, running power, reducing the waste of cold water and waiting time, suitable for water scarce areas, such as desert areas..
KOLERFLO circulation water pump RS15-6 Used in Suitable for city buildings, suburban villas, houses, water and pressurized with industrial equipment, air conditioning, boilers, solar circulating water, hot water circulating warm and so on.....

Check Stock

POWERENG 115V Hot Water Circulating Pump 3/4" NPT 3-Speed Hot Water Recirculating Pump for Solar Heater/Faucet (Blue)

.... NPT 3/4 inch (19.05 mm) inlet/outlet. Voltage/Frequency: 110-120V, 60Hz. Max pressure: 145 psi (10 bar),the circulation pump with three-speed control. Flow: 36/29/20 LPM (9.5/7.66/5.28 GPM). Max head: 6/4.9/4 m (20/16/13 ft).
Pump housing: Aluminum. Impeller: Corrosion-resistant, composite, PES. Shaft: 45 # steel. Bearing: Carbon axia..
2.Easy installation, only need a wrench to connect the pump to the pipeline, saving you the cost of plumbers.
Instant hot water, waiting for 2-3 minutes in the past, now it takes only 15 seconds to get hot water..
3.Prevent pipes from freezing in winter, especially for cold winter areas. In addition, if your pipes pass through the floor, the floor will also become warm..
4.The circulation water pump features high efficiency with low consumption. High temperature resistance, anti-fraying, high flow and leak-tightness. Super silent, environmental friendly,saving energy, running power, reducing the waste of cold water and waiting time, suitable for water scarce areas, such as desert areas..
5.POWERENG circulation water pump RS15-6 Used in Suitable for city buildings, suburban villas, houses, water and pressurized with industrial equipment, air conditioning, boilers, solar circulating water, hot water circulating warm and so....

Check Stock

Happybuy RS15-6 Hot Water Recirculating Pump 110V Circulation Pump 3/4-Inch NPT 3-speed Recirculation Pump 9.5 Gpm for Water Heater System

...let. Voltage/Frequency: 110-120V, 60Hz. Rated power: 93/67/46 W. Max pressure: 145 psi (10 bar),the hot water circulation pump with three-speed control. Flow: 36/29/20 LPM (9.5/7.66/5.28 GPM). Max head: 6/4.9/4 m (20/16/13 ft).
Pump housing: Aluminum. Impeller: Corrosion-resistant, composite, PES. Shaft: 45 # steel. Bearing: Carbon axia.
【CONVENIENT】 – Easy installation, just need a wrench to connect the pump to the pipeline, saving you the cost of plumbers.
Instant hot water, waiting for 2-3 minutes in the past, now it takes only 15 seconds to get hot water (the kitchen takes about 1 minute to get hot water due to low flow restriction).
【HUMANIZED DESIGN】 -Prevent pipes from freezing in winter, especially for cold winter areas. In addition, if your pipes pass through the floor, the floor will also become warm..
【ADVANTAGE】 – The hot water circulation pump features high efficiency with low consumption. High temperature resistance, anti-fraying, high flow and leak-tightness. Super silent, environmental friendly,saving energy, running power, reducing the waste of cold water and waiting time, suitable for water scarce areas, such as desert areas.
【WIDE APPLICATION】 – Our hot water circulation pump RS15-6 is suitable for ....

Check Stock

AQQA Aquarium Air Pump ,5W 10W Powerful 2 Outlets,Fashion Ultra-Quiet Energy-Saving Oxygen Pump Adjustable 4 Airflow Rate Grades,Freshwater and Marine Fish Tank 5W (up to 300 Gallon)

...metal grey,pump top with a royal-blue lamp,high-end atmosphere,Lights up when the button is pressed,The intensity of the light represents Flow Rate,Made of durable material using precision design results in a long lasting pump..
【Ultra-quiet Energy-saving，Suitable for Both Freshwater and Marine Aquariums】Use a bearing-less motor.It works using magnets, which means less vibration,resulting in lower noise than traditional bearing driven air pumps.Extra vibration and noise dampening systems on the pump further reduce the noise,making this ultra-quiet air pump perfect for bedroom aquariums!.
【Two Stainless Steel Outlets,Large Volume Oxygen Pump】Super-powerful with superior stainless steel outlets,perfect for running two sponge filters or air stones etc accessories.super large amount of perfect dissolved oxygen,It oxygenates your aquarium, pond and hydroponic systems.5W Air Flow 200GPH for fish tank 1 to 300 gallon,10W Air Flow 285GPH for fish tank 1 to 600 gallon..
【Adjustable Four Grades Flow Rate,Fast Heat Dissipation】To adjust the amount of air,press the“set” button then the brightness of blue light will be changed,the amount of air will be adjusted.The brighter the larger of airflow,after 5 second the light will be turned off.If it is ....

Check Stock

KOLERFLO 110V Water Recirculation Pump 120W Automatic Circulation Pump/Circulator Pump for Water Heater System(RS15-9 Red)

Max flow：30L/min；Rated Head：25.9FT.
Liquid Temperature range -10 – +110℃；Voltage: 110V/120V, Frequency:60Hz.
Inlet/Outlet: 3/4 inch.And there’s no other fittings only pump included for this package..
120W Powerful motor, the Most powerful Type of this boost pump. It Can be used with water heater or hot water pressurization system,but not for potable water system..
The built in flow switch will Automatically turns the booster pump off and on.you can also use it with a pressure switch..
No leakage, low noise, environmental protection, aesthetics, ease of installation and so on..
Compact and Durable: Pump housing: Cast Iron.
Impeller: Corrosion-resistant, Composite, PES.

Check Stock

Pump, Grinder, 2 HP, 15a

...of Water @ 5 Ft. of Head: 50 Hz: 60 Input Phase AC: 1.
GPM of Water @ 15 Ft. of Head: 50 Max. Liquid Temp.: 140 Degrees F Max. Head: 108.0 ft. Voltage: 208/230 Amps: 15 GPM of Water @ 10 Ft. of Head: 50 Item – Grinder Pumps: Grinder Pump Item: Grinder Pump GPM of Water @ 80 Ft. of Head: 27 Base Material: Cast Iron Bearing Type: Upper and Lower Ball GPM of Water @ 35 Ft. of Head: 50 Pump RPM: 3450 GPM of Water @ 40 Ft. of Head: 48.
GPM of Water @ 30 Ft. of Head: 50 Switch Type: Tether Impeller Material: Stainless Steel On Point: 15 Handle: Yes Housing Material: Cast iron Max. Head – Pumps: 108 ft. GPM of Water @ 45 Ft. of Head: 48 GPM of Water @ 70 Ft. of Head: 35 Min. Sump Pit Dia.: 24″ GPM of Water @ 50 Ft. of Head: 46 GPM of Water @ 25 Ft. of Head: 50 Switch Type – Pumps: Tether Impeller Material – Pumps: Stainless Steel.
Cord Length – Pumps: 25 ft. Pump HP: 2 Height: 19-1/2″ Phase: 1 Motor Type: PSC Length: 12-1/2″ FNPT GPM of Water @ 55 Ft. of Head: 45 GPM of Water @ 20 Ft. of Head: 50 Shaft Seal Material – Pumps: Silicon Carbide, Viton Agency Compliance: CSA C/US Duty: Continuous Voltage – Pumps: 208/230VAC Discharge NPT: 1-1/4″ F Max. Diameter Solids: 2 in Duty Cycle: Intermittent.
Switch Actuation: Tether Float Flow Rate @ 40....

Check Stock

Lidscura 8PCS Motorcycle Bearing Pullers 9-23mm Motorcycle Internal Bearing Removal Tool Kit Inner Bearing Extractor Kit

Widely Application: This Remover tool kit is ideal for internal bearing removal of automotive flywheel, motorcycle wheel, bicycle wheel, pump bearing generator bearing, machine bearing etc..
Meet Your Different Needs: Internal bearing Extractor tool set is equipped with 5 different sizes of open clips. The bearing can be disassembled from 0.35inch(9mm) to 0.91 inch(23mm) inside diameter..
Fine Workmanship: This motorcycle bearing pullers set is made of high-quality chrome vanadium steel, strong and durable for for a long service time..
Easy to Use: Connect this bearing puller kit with 1/2" 3/4" male thread water faucet, open clamps by turning handle clockwise to snug against the bearing for taking out the inner bearing..
Instructions for use: First the tool head into the inner ring of the bearing, and then screwed into the shaft, the tool head propped open hooked bearing inner ring, and then turn the shaft, you can pull out the bearing.

Check Stock

Outlaw Racing OR2690 Complete Water Pump Rebuild Repair Kit Shaft Gasket Seal Compatible with Honda CRF450R 2002-2008 - Replaces OEM Parts - All Necessary Gaskets Washers Seals and O-Rings

...TH HONDA- This water pump is compatible with Honda models CRF450R 2002, 2003, 2004, 2005, 2006, 2007 and 2008. Outlaw Racing kit is complete with all the parts that fit these models to ensure a perfect fit with no modifications needed..
✅ EVERYTHING YOU NEED TO REBUILD OR REPAIR YOUR WATER PUMP- The kit includes a bearing, pump shaft, and all necessary gaskets, washers, seals, and O-rings to repair your water pump. Say goodbye to leaky water pumps with our complete water pump repair and rebuild kit..
✅ HIGH QUALITY KIT TO REPLACE YOUR WORN-OUT STOCK UNIT- Most bikes are prone to water pump failures.
this kit will replace your worn-out stock unit at a fraction of the cost. Get back up and running more quickly with less downtime..
✅ YOUR SATISFACTION IS OUR #1 PRIORITY- We take pride in manufacturing motorcycle parts that save you time and money while not compromising on quality. Your safety and performance are what matters most. If you have any questions or concerns about your product, please reach out to us and we would be happy to assist you..

Check Stock

TOYMATE 480W Air Blower, Pump Fan Commercial Inflatable Bouncer Blower, Perfect for Inflatable Water Bounce House, Jumper, Bouncy Castle

♪ 【Safe Design】- Electric air blower has a clear cover on the switch, which is safe enough for you to turn on/off in case it gets wet. There are 2 wire meshes covering on 2 vents, which can protect our hands from getting cut when on working status. Our portable air blower pump uses a particular built-in bearing, which performs better than other plastic ones.
the air blower pump engine runs more smoothly..
♪ 【Compact & Portable】- This high pressure air blower pump with a handle on the top is easy and convenient to transport or carry.
The small size of this electric pump blower will take less space on your room, which is portable operation by one person independently..
♪ 【Wide Usage】- With 0.64 horsepower, strong and efficient 480 watts motor, 4-1/4” (outside) air outlet diameter, quickly filling and greatly air flowing, this air blower pump fan works well with outdoor bounce houses, water slides, obstacle courses, air sofas and other suitable inflatable bouncers..
♪ 【Silent Mode】- This air blower pump uses high-quality metal impellers, which greatly reduces its noise in operation.

Check Stock

Merkisa Hot Tub Booster Seat, Inflatable and Water Filled Hot Tub Seat with 4 Suction Cups, Durable Hot Tub Booster Seats for Adults Kids（Navy）

【Inflatable & Water-Filled Hot Tub Seat】 Merkisa hot tub seat can inflatable and water filled. Please note: injecting more than 2/3 of the water can be better placed underwater..
【Durable Materail】Adopted load-bearing, heat-resistant materials. Suitable for different water temperatures and various groups of people. (Bearing load：330 LBS /Size: 15.75*14.57*5.9 inch).
【4 Suction Cups】It can be easily filled with standard hose nozzles or electric air pump (we recommend using an electronic air pump to fill the seat cushion more fully). The suction cups can prevent the valve seat from floating or moving..
【Exquisite Design】Comfortable and attractive design, suitable for all spas and hot tubs.Perfect design It blends with the color of the water, as if floating in the ocean, making you feel relaxed and comfortable..
【Widely Used】Suitable for all spas and hot tubs,comfortable and attractive for both adults and children, especially great to use in elders bath as a sort of booster seat..

Check Stock

Wrench Rabbit New Complete Engine Rebuild Kits for Yamaha R Raptor (05-13), YFM 350 X Warrior (87-04) WR101-209 , Black

Vertex Piston Kit standard compression piston, rings, pin and clips. Hot Rods Heavy Duty crank stock stroke - includes wrist pin bearing for two strokes. Hot Rods main bearing/seal kit Hot Rods transmission bearing kit includes transmission bearings, output shaft collar and sprocket lock washer. Hot Rods counter balancer bearing. Kit Hot Rods water pump bearing and seal kit. Vertex complete gaskets kit including seals and O-ring kit (covers top and bottom). Hot Cams cam chain..
Fit: Convenient one stop shop in a box! Kit contains oversized +0.5mm piston kit, heavy duty crankshaft, main bearing and seal kit, balancer bearing kit, transmission bearing kit, waterpump bearing and seal kit, complete gasket and seal set, and cam chain (if applicable).
Meets or Exceeds OEM Specs for Fit and Performance.

Check Stock