ReviewsWelding Flow Meter

BISupply Heating Torch with 5 Meter Hose – Portable Torch Weed Burner Propane Torch Hose

  • [Propane Weed Burner Torch]: Whether you are removing weeds and ice, or soldering and cutting materials, the BISupply Welding Torch Flame Gun is perfect for all your needs.
  • This roofing torch generates temperatures up to 3000 degrees F (1649 degrees C) and connects to 20 lb. (9.1 kg) propane tanks (Tank not included).
  • [Versatile Tool]: This landscaping construction tool is perfect for homeowners, crafters, and professional contractors thanks to its versatility.
  • Burn weeds, melt snow, and remove paint using this propane torch.
  • Thaw pipes, heat roofing materials, and preheat metals for welding and soldering.
  • The lengthy torch and hose allow you to work safely and easily in hard to reach areas.
  • [Easy to Use]: Connect the blow torch and hose to the other end of the hose to a gas tank.
  • After ensuring all connections are sealed, slowly loosen the gas tank valve and check for leaks.
  • Slightly loosen the blow torch flow valve and ignite directly at the nozzle, adjust the blow torch flow valve to reach the desired temperature.
  • Fire will extinguish naturally to remove gases from torch and hose.
  • [Built to Last]: Constructed of stainless steel, these weed burners are resistant to rust and corrosio....
Check Stock

Horiba 9096001700 Plastic Body PH Electrode

  • Modular design makes it suitable for use with output modules, sensors and remote transmitters.Compact structure, easy to install.Intuitive clear reading, high reliability, measuring accuracy is ±1%.High-definition displays show both instantaneous and cumulative flow.Can be widely used to measure diesel, kerosene, gasoline, etc..
  • This digital turbine flow meter has modular design, high accuracy, compact size and stable performance. Easy to replace and maintain internal components. Suitable for use with output modules, sensors and remote transmitters..
  • Malfunction and solution:The flow meter is not accurate. 1. The method of field calibration is not correct. Calibrate again. 2. The flow rate on the meter is below the lowest. Increase the flow rate. 3. The flow meter is blocked by the dry liquid. Take out the impeller and clean it carefully and make sure the impeller turns freely..
  • 4. The impeller is wrapped by the sealing material. Remove the meter and make sure the impeller turns freely. 5. Too close to the impeller. Install properly 6. Too close to the motor or electronic noise environment.
  • The meter can not calibrate. 1. Circuit board is break down. Replace the circuit board. 2. Button is fail to press. Replace the circuit board..
Check Stock

Weldpro Omni 210 Dual Voltage 115V/230V AC/DC Multi-Process Welder - MIG/Flux Core/Stick/ACDC High Frequency TIG with Pulser and Aluminum Balance/Frequency Control 3 year warranty welding machine

  • Weldpro’s new 200 Amp Multiprocess welder now includes AC/DC TIG Welding with Hi Frequency Start and Pulse Control.MIG/Stick/ AC&DC TIG/ Flux Core/ Aluminum Spool Gun all new design with FOOTPEDAL and TRIGGER SWITCH..
  • Dual Gas inputs for dedicated Argon and MIX/CO2 tanks. MIG gun and TIG torch can be connected simultaneously for ease of switching between MIG and TIG.All new easy to use, multifunction data display and controls that make changing welding processes and parameters simple even for beginners..
  • 200A Welding Current across ALL PROCESSES allows welding of various thickness material and different types of base material..
  • Included VRD feature with Hi Temp and Overload protection with indicator. User adjustable inductance.Operates off 115V/230V standard household current.
  • What’s Included: 10ft NT1 MIG gun, 12ft CK 17-12-RSF Flex head TIG torch, 5AWG 10ft 200A electrode holder, 5AWG 10ft 300A T-shape earth clamp CGA 580 gas flow meter with 4.5ft gas hose, Power adapter, 0.030’’-0.035’’ knurled drive roll, 0.024’’-0.035’’V-Groove drive roll, AK-3 accessory kit, Weldpro CK17 torch protection cover, Trigger button for TIG torch, Weldpro SSC control foot pedal.
Check Stock

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

  • FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
  • MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
  • HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
  • INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
  • MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..
Check Stock

CGOLDENWALL Turbine Flow Meter Digital Fuel Flowmeter with FNPT Inlet/Outlet, 1inch Flow Meter for Water Diesel Kerosene Gasoline, 2.5-26GPM /9-100LPM (1 inch)

  • FLOW METER: the 1 inch flow meter can read instantaneous flow rate, single cumulative flow and total cumulative flows. But it has minimum flow rate requirment, if the flow rate of the tested liquid is lower than 2.5 gal/min, the readings will be inaccurate..
  • TECHNICAL PARAMETERS:① diameter of water inlet: 32mm.
  • ③ the flow speed requirenment for tested liquid: 2.5~26 gal/min.
  • ⑥ max temp of tested liquid: 158°F/70°C.
  • MULTIPLE UNITS: the flow meter provide 4 meauring units for option, which are liter, gallon, pint and quart. The unit defaults to gallons, if the unit is not gallons, please refer to the user manual to change the unit to the needed one..
  • NOT WATER PROOF: the flow meter is not water proof, please keep the display from water during use, to avoid chip damage. We upgraded The flowmeter has been upgraded from never-sleep model to auto-sleep model, which automatically dims the screen when no liquid is flowing through it..
  • WIDE APPLICATION: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids. If there is any problem, please contact us in time..
Check Stock

MEANLIN MEASURE Argon Regulator Flow Meter with 6.5 Feet Hose,CGA580 Inlet Connection,5/8' x 18RH Outlet Fitting,Dual Output Argon Welding Flowmeter for TIG MIG Welder

  • 【Easy to Read】2″ gauges for easy reading. Makes adjusting your pressure values a piece of cake..
  • 【CGA-580 Inlet】This Gas Pressure Regulator Can Be Used with Argon, Helium and CO2 Gas Tanks,Ideal for MIG and TIG welding applications..
  • 【Accurate Measurement】This Gauge measuring range 0-4500PSI,It has a highly sensitive pointer to sense the pressure in the pressure tank,so it is more reliable than the flow-gauge style..
  • 【Excellent Quality】Our Double Dutput Argon Regulator Is Made Of Brass For High Strength, Toughness And Corrosion Resistance For Long Term Use..
  • 【Package Include】1*Argon Regulator Flow Meter 1* 6.5Feet Hose 2*Male 5/”8 UNF-18RH Fitting 2*1/4″ Hose Barb Adapter 2*Female 9/16″x18 Nut.
Check Stock

Grow Crew Hydroponic CO2 Enrichment Kit | Includes 20 lb Aluminum CO2 Tank, Carbon Accelerator C02 Regulator, Atlas 7 CO2 PPM Monitor and Active Air Rain System to Shower Your Plants with CO2

  • ...2 TANK - The 20 pound aluminum tank is brand new, and perfect for use with our CO2 regulator. Aluminum tanks are about 1/2 the weight of standard steel tanks and do not rust or corrode. A 20 pound tank should last about a month in a 5’ x 5’ grow room, and can be filled at most any beverage / beer distributor or welding supply store for around $25. Due to shipping restrictions the tank ships empty, not filled..
Check Stock

VIVOSUN Argon/CO2 Regulator Emitter System with 50 PSI Fixed Max 4000PSI Inlet Pressure Precise Brass Regulator for Gas Control in Hydroponic Grow Tent House Aquarium Welding

  • Durable Material: This regulator’s body is made of high-quality brass, which has high strength, high toughness and corrosion resistance, and strictly tested to ensure long -term use.
  • Precise Control and Measurement: This regulator equipped with a flow meter and pressure gauge.
  • Output flow is indicated by a ball in the flow tube and is adjustable from 10 to 60 SCFH.
  • The pressure gauge ranges from 0 to 4000 PSI and is used to read the amount of gas remaining in the tank.
  • CGA-580 Tank Inlet: The regulator fits standard Argon and CO2 gas tanks with CGA-580 inlet connection, and has a unique filter port design on the CGA-580 mounting port.
  • Two Connection Ways: There are female 5/8" x 18 outlet nut and a standard 1/4" barb adapter, you can choose the connection method of the hose according to your needs.
  • Multiple Applications: Suitable for indoor grow rooms, grow tents, greenhouses and hydroponics to increase CO2 in the growth environment for optimal growth.
  • And ideal for MIG TIG welding, chemical, and electronics industries.
Check Stock

Fox Alloy 20pcs Copper Brazing Rods BCuP-2 (5/64\) 2mm Phosphor Round Self Fluxing Copper Welding Rods Sticks TIG Arc Pipes for Air Conditioner Refrigerators

  • Material: The package includes 20PCS 2.0mm cooper brazing rods BCuP-2 brass welding rod.
  • Standard: The copper welding rods kit conforms to AWS A5.8.
  • Advantage: The low temperature phosphor copper welding rod is easy to install and remove. Good fluidity during welding, can flow into small space. Low metling point 640-770℃, good fluidity during welding, molten metal can flow to small gaps.
  • Application:The stick TIG welding rods is used for brazing of copper & copper alloy in motors, air-conditioners, meters, and refrigeration industry.
  • Service: Fox Alloy Time-proven formulation.
  • A team of experienced welding engineers ready to answer all your welding questions..
Check Stock

Flow Meter,Aluminum Alloy 1/2 inch Digital LCD Display High Accuracy Fuel Diesel Flowmeter Water Flow Rate Sensor,Control and Measure Low Flow for Gasoline,Kerosene,Engine Oil Blue

  • ✔【DIGITAL LCD DISPLAY】The aluminum alloy flow meter has LCD screen display, which can provide clear reading. Meanwhile, the LCD display flow....
  • ✔【READING AND ACCURACY】There aluminum alloy fuel diesel flow meter has intuitive clear reading and high reliability on digital stainless steel....
  • ✔【WIDE COMPATIBILITY】The high accuracy fuel flow meter is suitable for high viscosity liquid media such as diesel, gasoline, kerosene, engine....
  • ✔【RELIABLE QUALITY】The blue LCD display high accuracy aluminum alloy fuel diesel flow meter is 100% brand new and high quality. Meanwhile, it is....
  • ✔【100% WARRANTY】We promises every customer a 100% shopping satisfaction, feel free to reach us if you have any questions about your purchase.We....
Check Stock

Forney 85364 MIG Gas Flow Meter and Regulator, MIG/TIG Welders

  • Combination of regulator and flow meter as one single stage piston design unit.
  • Provides accurate regulation of gas flow.
  • Impact resistant machined brass body, polycarbonate flow tube and outer cover.
  • Features regulator and flow meter in one unit.
  • Provides accurate regulation of gas flow designed for MIG and TIG applications.
Check Stock