ReviewsWelding Fume Exhaust System

KOTTO Strong Suction Hose Fume Smoke Absorber for Soldering Electric Iron Welding 3d Printing Extractor Absorber Remover DIY Extractor Carbon or HEPA Filter,2 Pack Set Replacement HEPA Filter

  • Soldering Smoke Absorber, Electric Iron Welding Fume Extractor Soldering Smoke Absorber Remover DIY Fume Extractor Filter with Strong Suction..
  • A 24-inch flexible tube, Fume hood can adjust direction according to actual needs..
  • Adjustable optimized 6000 RPM high suction fan is low noise and allows you to remove fumes 5-6 inches away. The fan speed is adjustable. Suction: 40W,....
  • Replacement HEPA Filter for Solder Smoke Absorber..
  • Replacement HEPA Filter absorbs and captures fumes from solder, flux, chemicals, gases and helps to prevent dissipation into the room..
Check Stock

Fox Alloy E71T-GS .030\ Flux Core Welding Wire Gasless Mig Wire - 2 Lbs Spool Welding Wire Mild Steel Filler Metal (0.8 mm)

  • 2-lb spool 0.030" gas-less E71T flux-cored ( FCW ) mild steel MIG welding wire with sturdy packaging, and comes with a 0.030'' contact tip.
  • Welding Wire E71T-GS conforms to AWS A5.20 (E71T-GS), AWS A5.36 (E71T14S-AZ-CS3), ISO 17632-A (T42 Z Z V N 1).
  • Flux core welding wire E71T-GS is self shield, no shielding gas needed, single-pass fillet and lap welding, all positional, low welding fume, minimum spatter,Smooth arc action,High feedability,Filler Metal welding wire is easy to weld in indoor and outdoor.
  • Mild steel welding wire E71T-GS is applied in welding of thin plate steel structure, i.e, doors， fence..
  • A team of experienced welding engineers ready to answer all your welding questions.
Check Stock

Flexadux T-7SR Thermoplastic Rubber Duct Hose, Black, 4\ ID, 0.024\ Wall, 25' Length

  • Duct hose for industrial ventilation, dust removal, fume exhaust, and light bulk material handling.
  • Black, thermoplastic, rubber-coated, reinforced, non-woven polyester fabric, reinforced with a spring steel wire helix, is resistant to abrasion, tearing, chemicals, ozone, moisture, and ultraviolet (UV) light.
  • Flexible and compressible for handheld use and easy installation.
  • Suitable for applications with temperatures up to 285 degrees F, such as fume extraction and industrial ventilation.
  • More resistant to tears, punctures, and abrasion than woven neoprene and standard thermoplastic rubber hoses.
Check Stock

KOTTO Strong Suction Hose Fume Smoke Absorber for Soldering, Electric Iron Welding, 3d Printing Extractor Absorber Remover DIY Extractor Carbon or HEPA Filter [Updated, Hose pre-attached]

  • Soldering Smoke Absorber, Electric Iron Welding Fume Extractor Soldering Smoke Absorber Remover DIY Fume Extractor Filter with Strong Suction..
  • A 24-inch flexible tube, Fume hood can adjust direction according to actual needs..
  • Adjustable optimized 6000 RPM high suction fan is low noise and allows you to remove fumes 5-6 inches away. The fan speed is adjustable. Suction: 40W, 6000 RPM, 52CFM, Noise Level: 55dbm, Life Expectancy: 50,000 hours, Static pressure: 125mmH2O..
  • Easy to replace the filter, Includes one replacement filter. Working temperature: -20℃～60℃, Power consumption: 120V-240V, 40W ( 12V, 4A Power supply)..
  • US-based customer support, 30 days full satisfaction no question asked return period..
Check Stock

KEMIMOTO Compatible with Grom MSX125 Low Mount Exhaust Slip-on Muffler Baffle 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023

  • ...Install】: Installing the exhaust on your grom bike is also relatively easy as you just need to slip it right on and then install the bracket without looking at any instructions. It comes with a clamp and hardware for even easier, hassle-free installation. The whole process should take you around 10-15 minutes. No welding is required..
  • 【Complete Accessories 】: The muffler exhaust comes with complete accessories including a DB killer, springs and hooks, stable clamps, mid connect pipe which is easy to install..
Check Stock

Solar Panel Fan Kit 10W 12V Solar Powered Fan Outdoor Waterproof Portable Ventilator Exhaust Fan with 2M Long Cable for Chicken House Greenhouse Pet Houses Shed

  • This exhaust fan is powered by monocrystalline solar panels. Outdoor solar panels can effectively convert sunlight into electricity. The efficiency of....
  • The exhaust fan can keep the air clean, and can also help you eliminate the smell of pets and oil fume..
  • The solar panel exhaust fan is equipped with a standard USB regulator, which can maintain a 5~6V output..
  • The size of the exhaust fan is about 120 x 120 x 25 mm/4.7 x 4.7 x 1.0 inches. There are 4 suction cups in the package. The exhaust fan can be....
  • This solar exhaust fan has an IP65 waterproof rating, safe and durable, suitable for greenhouses, pet houses, tree houses and RVs, etc., to maintain a....
Check Stock

Denshine Class 100 (Fed 209E) Vertical Ventilation Laminar Flow Hood Air Flow Clean Bench Workstation 110V Vertical Flow Laminar Flow Hood Fan Air Clean Bench for Lab and Industry - Shipping from USA

  • Fume hood has a molded, one-piece outer polyethylene shell for durability and chemical-resistance, with a clear acrylic door panel that slides up and down on inside tracks.
  • Large body measures 30 x 20 x 42 inches (H x W x D), with a 14.2 x 34.5 inches (H x W) door opening.
  • Door positions include open, closed, or intermediate.
  • when in closed position, the sash remains slightly open to facilitate continuous air flow.
  • Exhaust stack connection has a 15 cm outer diameter (OD).
  • works with an exhaust system (not included) that draws free air at 350 cubic feet per minute (CFM).
Check Stock

AUTOSAVER88 4 Inch Inlet Exhaust Tip, 4' Inlet 6' Outlet 15' Long Chrome Polished Finish Stainless Steel Universal Exhaust Tail Tip for 4' Outside Diameter Tailpipe, Rolled Angle Cut, Bolt On, Silver

  • Dimension: standard 4″ x 6″ x 15″(inlet, outlet and overall length).
  • ONLY universal fit for vehicles with 4-inch outside diameter exhaust pipes (please make sure the Outside Diameter of your vehicle tailpipe outlet is 4.0″ before purchase).
  • Anti-deformation & rustproof: built from high-grade stainless steel, our exhaust tips effectively resist heat, rust and deformation to protect & decorate your tailpipe system well.
  • plus, a drainage hole helps drain water to prevent rust.
  • Stylish & pleasant-sounding: sleek degree rolled-edge angle cut and thicker inner wall design, make your car sounds rumble and crackle for a more powerful and unique sound.
  • meanwhile, the chrome polished finished offer your car with a a new & sporty appeal.
  • Easy installation: the bolt-on design makes it super easy to fasten to your exhaust pipe with M8 Allen Key, no drilling or welding needed.
  • Daily Maintenance: To make this exhaust tip has a long-life service – Please Sweep away the welding debris, cement, oil, white ash, putty, sand ash regularly to keep the surface clean. We recommend to do above action once a month (NOTE: Professional installation would be highly recommended).
Check Stock

AUTOSAVER88 3 Inch Inlet Black Exhaust Tip, 3' Inlet 4' Outlet 12' Overall Length Stainless Exhaust Tips Powder Coated Finish Tailpipe, Universal Fit for 3' O.D. Tailpipe, Rolled Edge, Bolt/ Clamp On

  • Dimension: standard 3″ x 4″ x 12″(inlet, outlet, and overall length).
  • ONLY universal fit for vehicles with 3-inch outlet diameter exhaust pipes (please make sure the Outer Diameter of your vehicle tailpipe outlet is 3″ before purchase).
  • Anti-deformation & rustproof: built from high-grade stainless steel, our exhaust tips effectively resist heat, rust and deformation to protect & decorate your tailpipe system well.
  • plus, a drainage hole helps drain water to prevent rust.
  • Stylish & pleasant-sounding: sleek 20-degree rolled-edge angle cut and thicker inner wall design, make your car sounds rumble and crackle for a more powerful and unique sound, meanwhile, the Black Powder Coated Finish offer your car with a elegant and mysteriou appeal.
  • Easy installation: the bolt/ clamp-on design makes it super easy to fasten to your exhaust pipe with M6 Allen Key, no drilling or welding needed.
  • Daily Maintenance: To make this exhaust tip has a long-life service – Please Sweep away the welding debris, cement, oil, white ash, putty, sand ash regularly to keep the surface clean. We recommend to do above action once a month (NOTE: Professional installation would be highly recommended).
Check Stock

AUTOSAVER88 3 Inch Exhaust Tip, 3' Inlet 4.5' Outlet 9' Overall Length Chrome-Plated Finish Tailpipe Stainless Steel Exhaust Tips for 3' O.D. Tailpipe, Rolled Edge Slant Angle Cut, Bolt On, Universal

  • Dimension: standard 3″ x 4.5″ x 9″ (inlet, outlet and overall length).
  • ONLY universal fit for vehicles with 3-inch outlet diameter exhaust pipes (please make sure the Outer Diameter of your vehicle tailpipe outlet is 3″ before purchase).
  • Anti-deformation & rustproof: built from high-grade stainless steel， our exhaust tips effectively resist heat, rust and deformation to protect & decorate your tailpipe system well.
  • plus, a drainage hole helps drain water to prevent rust.
  • Stylish & pleasant-sounding: sleek degree rolled-edge angle cut and thicker inner wall design make your car sounds rumble and crackle for a more powerful and unique sound.
  • meanwhile, the chrome-plated finish would give your car a new & sporty appeal.
  • Easy installation: the bolt/ clamp-on design makes it super easy to fasten to your exhaust pipe with M6 Allen Key, no drilling or welding needed.
  • Daily Maintenance: To make this exhaust tip has a long-life service – Please Sweep away the welding debris, cement, oil, white ash, putty, sand ash regularly to keep the surface clean. We recommend to do above action once a month (NOTE: Professional installation would be highly recommended).
Check Stock

ZOEYES 4 PCS Stainless Steel Exhaust Elbow, 2.5”Mandrel Bend Elbow - Thickness 16GA/.065”Wall, SS304 Stainless Elbow for Car Modified Exhaust Elbow Pipe, Stair Handrail, 90 Degree

  • Parameter - 2.5”Exhaust pipe 90 degree elbow.
  • Diameter: 2.5inch, Bend Degree: 90º, Wall Thickness: 16GA/.065”, Back arc length: 6inch (These elbow exhaust pipes can be welded to 2.5”OD tube).
  • Sturdy & Durable - Our 2.5”elbow exhaust pipe made of premium SS 304 stainless steel, smooth edge and mirror polishing.
  • Not easily damage, anti-rust, anti-oxidation 2.5 exhaust pipe.
  • Easy to Install - Laser cut end make the pipe ready to weld and easy to use, the elbow exhaust will save your time and energy.
  • Wide Application - These universal exhaust pipes are suitable replacement for your car modification, stair handrail welding, or complete own custom DIY exhaust system.
  • Package List - You will get valued 4 pieces of 90 bend elbow pipes.
  • No pollution: healthy, environmentally friendly, non-toxic and non-polluting.
Check Stock