ReviewsWire wound Fuse Resistors

iBrightstar 50W 6ohm Load Resistors for Fix LED Bulb Fast Hyper Flash Turn Signal Blink Error Code

2PCS 50W 6ohm Load Resistors + 4PCS Quick wire Clip..
Prevent LED Turn Signal Lights or License Plate Brake Lights from hyper flashing, malfunction or trigger warning message on dashboard..
NOTICE! Load Resistors heat up like light bulbs and get super HOT when working. Make sure you mount them away from any wires or plastic..
One resistor is required for each turn signal bulb or each license plate light bulb..
Easy installation. Just connect the wires with the splice taps provided and no wire cutting is necessary..

Material:copper+rubber, Fuse holder dimension:38x25x13mm.
In-line fuse holder for mini blade fuses, Suitable for 1A,2A,3A,5A,7.5A,10A,15A,20A, ideal for car truck atv boat.
14 AWG thick red pigtail wire allow you to cut and splice it into any project, Wire length:30cm/12inches, Wire range:14 AWG.
Waterproof design, the rubber cap fits on tightly to protect any mini blade fuse inside.NOT easy to fall off or let water in..
Package Included: 2 X Mini Blade Fuse Holder and 2 X 15A Mini Blade Fuse.

10 AWG thick red pigtail wire allow you to splice it into any project..
Wire length: 6 inches 10 gauge wire each side, Fuse holder dimension: 41x35x15mm.
Waterproof design, the rubber cap fits on tightly to protect any standard blade fuse inside. NOT easy to fall off or let water in..
Inline Fuse Holder for standard blade fuses, Suitable for 1A,2A,3A,5A,7.5A,10A,15A,20A,30A,40A, ideal for car truck trailer atv boat marine.
Package Included: 2 X Standard Blade Fuse Holder and 2 X 40Amp Standard Blade Fuse.

CELLPOWER CPUSB01 12V to 5V MiniUSB Power Adapter with BDP (Battery Discharge Prevention) Low Voltage Cut-Off for Street Guardian SG9665GC (and other mini-USB powered) DashCam products.
Please search for SGDCHW for use with SG9663DC. Hard wire power directly to your DashCam (miniUSB powered) 12-24 Volt Compatible..
You can wire the CELLPOWER CPUSB01 miniUSB BDP hard wire kit to a “Switched” Accessory fuse power circuit and it will turn on/off with the car engine. Tip: Be sure to actually start the engine when testing Switched ACC power, turning the key one notch to ACC without starting the engine is too low on some cars.
You can technically wire it to “Non-Switched” Battery fuse power circuit, but we recommend the Vico-Power Plus or MotoPark Fine Safer for parking mode operations.
Total Length = 13 feet / (4 meters) miniUSB side = 8 feet / (2.5 meters) fuse panel side wire = 5ft (1.5 meters) Red/Black wires are 16 AWG *Note, Add-a-fuse pigtail not included (5A fuse is ok).

More humanized design with 50 pcs frequently used resistors (100, 220, 1k, 10k Ohm) and 25 pcs seldom used resistors. Color Code Guide helps you read the resistance.
Perfect pin (0.022 inches, 0.55mm), #24 lead SWG (Stand Wire Gauge), perfect for breadboard in electronic projects.
Perfect packaging: Plastic case + PE bag.

18 Ft.- 1/0 Gauge Red Power Wire CCA (Copper Clad Aluminum)/ 3 Ft.-1/0 Gauge Black Ground Wire CCA (Copper Clad Aluminum).
16 Ft.- 14 Gauge Clear Speaker Wire/ 18 Ft.- 18 Gauge Blue Remote Turn-On Wire.
18 Ft.- Twisted Pair RCA Interconnect Cable/ 0 Gauge Black Wire Loom.
Heat Tested, Water Resistent InLine ANL Fuse Holder/ 200 Amp ANL Fuse/ 3 Positive (+) and 2 Negative (-) Connecting Terminals/ Wire Ties.
Wire Gauge Set To International Wire Gauge (Not AWG). Bulk Packaged. Not for Resale..

VERSATILE FUSE HOLDERS ON THE MARKET: NVX’s XF-Series comes in two different sizes. Same technology, same function, but come in different sizes. The NVX XFMMINI accepts 4-8 wire gauge while the NVX XFMANL accepts 0-4 wire gauge. To change the size of the wire gauge you need, all you have to do is change the adapter collar to the correct wire size..
CONNECTS TOGETHER: NVX’s XF-Series of fuse holders now allows you to connect them together. The male and female connectors are located on the side of the fuse holder. Attaching them together is as simple as snapping the pieces together. No extra screws are required to connect them together. Each pack comes with power links to transfer power from one fuse holder to another..
GENERAL FEATURES: See-through windows allow for easy inspection | High-temperature, impact-resistant plastic casings | High conductivity plating | Ultimate circuit protection.

Heavy duty in-line fuse holder, ideal for mini blade fuse, for car boat truck auto use, added protection to the circuit..
Mini size in-line fuse holder, ideal for ATM blade fuse, come with cover, protects it from dirt and muddy water..
14 AWG wire, easy to automotive installation, cars, boats, motorbikes and trucks..
Package included: 20 pcs in-line fuse holder14AWG Wire..

KICKER brass hardware uses Versa-Gauge connection points with oversized convex screws for rock-solid connections..
The wire receptacles work with most size wire for clean, sharp install and a negative-post adapter collar that locks into place for a tight grip..
The KICKER FHD Dual Fuse Holder accepts 1/0 – 8 AWG power cables and accommodates any size AFS fuse..
FHD AFS Fuse Holder, 1/0-8AWG in/out, Dual Fuse.

18 Ft.- 1/0 Gauge Red Power Wire CCA (Copper Clad Aluminum)/ 3 Ft.-1/0 Gauge Black Ground Wire CCA (Copper Clad Aluminum).
16 Ft.- 14 Gauge Clear Speaker Wire/ 18 Ft.- 18 Gauge Blue Remote Turn-On Wire.
18 Ft.- Twisted Pair RCA Interconnect Cable/ 0 Gauge Black Wire Loom.
Heat Tested, Water Resistent InLine ANL Fuse Holder/ 200 Amp ANL Fuse/ 3 Positive (+) and 2 Negative (-) Connecting Terminals/ Wire Ties.
Wire Gauge Set To International Wire Gauge (Not AWG). Bulk Packaged. Not for Resale..

1/0 Gauge Red CCA (Copper Clad Aluminum) Power Wire: 17 Feet / Black CCA (Copper Clad Aluminum) Ground Wire: 3 Feet.
In-Line ANL Fuse Holder/ 180 Amp ANL Fuse.
2- Positive (+) Red Ring Terminals / 1- Negative (-) Black Ring Terminals / Installation Accessories/ Connectors/ Wire Ties/ Zip Ties: 8 PCS..
Wire Gauge Set To International Wire Gauge (Not AWG). Bulk Packaged. Not for Resale..