ReviewsXbee Breakout Board

Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino

  • Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
  • Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
  • The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
  • There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
  • Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
Check Stock

3 Axis Stepper Motor CNC Router Kit Nema23 425oz-in 112mm Dual Shaft+CW5045 Driver 4.5A 256 microstep+400W 36V Power Supply CNC Controller Kit for Engraving Lathe Plasma Milling Drilling Machine

  • ♞【Product】3 Axis nema23 stepper motor driver controller kit.
  • ♞【Application】This cnc kit are widely used in engraving machine, printer,....
  • ♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
  • ♞【Driver】CW5045 driver Voltage: DC 24-50V.
  • Current: rated maximum output reaches: ±4.5A.
  • ♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
  • ♞【Power supply】400W,36V/9.7A switching power supply.
Check Stock

C25S - Smooth Stepper Terminal Board

  • Full access to all the pins of the Smooth Stepper Board. Connects directly to the Smooth Stepper (from Warp9). The board is provided with sockets that allow the Smooth Stepper Board to be plugged directly into this board. No ribbon cables required. When using the Smooth Stepper board there is no need to use an additional power supply to power the board. It will draw power from the Smooth Stepper board. Built-in Passive Low Pass Filters for the all inputs..
  • C25 Smooth Stepper Breakout Board with push lock terminals.
Check Stock

DIGI XBP9B-DPST-001 RF TXRX Module XBee-PRO 900HP S3B Point2Multipoint 900MHz 250mW RPSMA 10Kbps

  • Plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee..
  • This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version.
Check Stock

Treedix RPi GPIO Terminal Block Breakout Board Module Expansion Board Compatible with Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W

  • Easy to operate: Use this module to easily extend the Raspberry pi Zero project to the Internet of Things or industrial control applications.
  • There is a mark on the breakout board that can clearly identify the pin position, Breakout board is of excellent quality and adopts double-sided gold forming process.
  • The module is small in size and does not occupy other space. It is very convenient when making DIY circuits, and the wires can be easily inserted into the terminals.
  • Compatible with Raspberry Pi: This GPIO terminal block is compatible with Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W.
  • Note: This project needs to be welded and assembled by yourself.
Check Stock

Atomic Pi Developers Kit

  • Powerful Atom quad-core processor with 2Gb ram and 16GB Flash on board.
  • Developer kit includes large breakout board and AI camera module.
  • Gigabit Ethernet, AC WiFi, Bluetooth, Hi Performance Audio, USB-2, USB-3, SD, GPIO.
  • Peripherals include 9-axis sensor, bluetooth and XMOS audio power-amp.
  • Boots Linux right out of the box. What will you make with it?.
Check Stock

4 Axis Stepper Motor Nema 23 Dual Shaft 425oz-in 112mm+CW5045 Driver 4.5A 256 Microstep+5 Axis Breakut Board+400W 36V Power Supply CNC Controller Kit for CNC Router Engraver Milling Machine

  • ♞【Stepper Motor】4pcs 23HS2430B nema23 stepper motor.
  • ♞【Stepper Motor Driver】4pcs CW5045 driver, current: 1.3A-4.5A.
  • Driver microstep: 1 (1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5,....
  • ♞【Control Board】1pcs 5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
  • ♞【Power supply】1pcs 400W,36V/9.7A switching power supply.
  • ♞【Application】This cnc kit are widely used in engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile....
Check Stock

S-Union [8PCS] New 16AWG 6Pin PCI-E to 8 6+2 pin Cable 27.5 Inch 70CM Length PCI 6Pin Male to Male Cable for GPU/PSU Breakout Board GPU Ethereum ETH Mining Power Supply with 5 Nylon Cable Ties

  • 【Item】PCI-E 6Pin to 8 (6+2) pin Male to Male Cable.
  • 【Safety】This item is 16 AWG wire，Able to withstand greater current and high power appliances.
  • 【Feature】The line is 27.5 inch (70CM) long, easy to use and connect.
  • 【Compatibility】This item is Compatible with Graphics Video Card, GPU breakout board,GPU Mining Power Supply, for GPU breakout board Search:....
  • 【What You Get And Shipping】8 x PCIe 6Pin to 6+2 Pin Male to Male Cable & 5x Nylon Cable Ties. SHIPPED FROM THE U.S. Delivery time takes about 2-5....
Check Stock

BIQU LCD 12864 Version Graphic Smart Display Controller Module with Adapter and Cable for RAMPS 1.4 Reprap 3D Printer Kit

  • 2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
  • RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
  • LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
  • A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
  • Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....
Check Stock

DAOKI 2 pcs 1.7-5V LSM6DS3 Module 6 Degrees of Freedom Breakout IIC/SPI Transfer Digital Sensor Vibration Sensor Module Acceleration Sensor Accelerometer Gyro Embedded with Dupont Line

  • 【Application configuration】: Each LSM6DS3 Breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DS3 Breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!.
  • 【Basic features】: The LSM6DS3 is a accelerometer and gyroscope sensor with a giant 8kb FIFO buffer and embedded processing interrupt functions, specifically targeted at the cellphone market. Due to the capabilities and low cost of the LSM6DS3 we've created this small breakout board just for you!.
  • 【Special Note】: Please be aware that the LSM6DS3 is a 3.3V device so that powering voltages above ~ 3.6V can permanently damage the IC. A logic level change is required for any development platform operating at 5V..
  • 【Data accuracy】: LSM6DS3 is capable of reading accelerometer data up to 6.7 kS / s and gyro data up to 1.7 kS / s for more accurate motion detection..
  • 【Original manufacturing】: 100% of our products are made of original electronic components, please rest assured to buy and use.
Check Stock

ACEIRMC 3pcs ESP32 Breakout Board GPIO 1 into 2 for 38PIN Narrow Version ESP32 ESP-WROOM-32 Microcontroller Development Board

  • Only suitable for 38PIN narrow version ESP32 without mounting holes, not suitable for other versions..
  • This breakout board can expand one GPIO pin of esp32 development board to two, which is convenient for users to reuse all pins in smart home projects. Nice breadboard alternative..
  • 2 TYPE CONNECTIONS， Pin Header & Screw Terminal. Just select them according to your purpose..
  • The expansion board is a double-layer board. One pin is wired on both sides. Therefore, the circuit is stable and highly reliable, and there will be no poor circuit contact and unstable signal transmission..
  • The board of this version has been soldered completely. No need to solder parts by yourself, which is very convenient to use..
Check Stock